manualshive.com logo in svg

Amana A1200S, Service, Page: 43 / 75

Share
Download
Amana A1200S Service Download Page 43

43

RE220002   Rev. 6

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

VEND-10, 11  Programming  Instructions

Programming times only

Any button may be programmed for heating times from 1
second to 39 minutes and 59 seconds (:01 to 39:59)

To reprogram the times you want:
1. Open the oven door; leave it open.
2. Enter the programming code "614" (push buttons 6,

1, and 4).

3. Close the oven door, note "PROG" in the display

which indicates you are in the Program Entry Mode.

NOTE:  Some flickering in the display during

programming is normal.

4. Push the button to be reprogrammed.  Note that the

button number and programmed time appear in the
display.

5. To change cook times:

Push and hold in button 1

to change seconds

"00:01"

Push and hold in button 2

to change tens of seconds

"00:10"

Push and hold in button 3

to change minutes

"01:00"

Push and hold in button 4

to change tens of minutes

"10:00"

NOTE:

If you miss the number you want, continue to

hold.  Momentary pushes will advance the count
one number at a time.

6. When you have entered  the time you want, push

button 5, 0 and 5.

7. If you want to reprogram another button, repeat steps

4, 5, and 6.

8. When you have completed programming the buttons

you wish to change, open and close the oven door to
exit the programming mode and go back to normal
operation.

Programming notes:
1. If you make an error while programming, push the "0"

button once to clear the error.  Go back to the
programming step you were performing.

2. If two stage heating has been previously

programmed, total time for a button will be defrost
time plus the time you just programmed.

See two stage programming instructions below.

Programming Defrost II First Stage Only

1. Open the oven door; leave it open.
2. Enter the programming code "614" (push button 6, 1

and 4).

3. Close the oven door, note "PROG" in the display

which indicates you are in the programming mode.

4. Push the button to be reprogrammed.  Note that the

button number appears in display and power level;
100% or Defrost II appears in the display.

5. To change to Defrost II, push Defrost II button.
6. When you have completed programming the buttons

you wish to change, open and close the oven door to
exit the programming mode and go back to normal
operation.

Programming Times and Two Stage Heating

Any button may be programmed for:
• Heating times from 1 second to 39 minutes and 59

seconds 9:01 to 39:59)

• Power level;  100% or Defrost II
• "Two Stage" cooking:  Defrost II (up to 39:59) plus

100% power, (up to 39:59) combined into a single
button.  This allows you to defrost and reheat food to
serving temperature with a single button push.

Summary of Contents for A1200S












































































Reviews:

No comments