Amana A1200S Service Download Page 30 | Manualshive

Page: 30 / 75

Amana A1200S Service Download Page 30

RE220002 Rev. 6`

30

Troubleshooting Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

Directions for System Diagnosis Flow Chart

A test set-up is described at the beginning of each test sequence. Directly below the test set-up is a description of
the normal oven operation(s) (identified by a question mark).
If oven operation is normal, follow the YES sequence down the left side of the page.
If oven operation is abnormal, follow the NO sequence to the right side of the page.
To effectively use this flow chart, the directions below must be followed:
• Always start at test sequence 1, perform each test set-up, do not skip test sequences.
• Verify normal operation(s) following each test set-up before going on to the next test sequence or set-up.
• When abnormal operation is identified, disconnect power to the oven,

DISCHARGE CAPACITOR(S), determine

cause

starting with the first possible cause, correct the failure, then start over at test sequence one to verify

normal operation.

NOTE: Always check for failed or improper wiring before servicing.

Diagnosis for VEND-10.000, .A, .B, .C, FS-10EVP, FS-14, FSP-10

Test Sequence 1: Idle Condition

Open oven door and connect power cord.

1.

No power applied to the oven power cord.

2.

Blown fuse (Note: Check interlock switch
module operation, monitor test).

Colon appears in the display?

No

3.

Inoperative cavity thermal protector.

4.
5.
6.

Inoperative low voltage transformer.
Inoperative controller.
Broken or improper wire connection.

Close oven door

1.
2.

Inoperative holding relay.
Inoperative controller.

Cavity light is on?

No

3.

Inoperative low voltage transformer.

Yes

4.
5.

Inoperative cavity light or socket.
Broken or improper wire connection.

Does the blower motor operates?

No

1.

Blower motor inoperative or binding.

2.

Broken or improper wire connection.

Yes

Stirrer motor operates?

No

1.

Inoperative or binding stirrer motor.

2.

Broken or improper wire connection.

Yes

"Idle" operation normal.
Proceed to "Cook" condition
(Test Sequence 2).

Yes

«
...
28
29
30
31
32
...
»

Summary of Contents for A1200S












































































Reviews:

No comments