Amana A1200S Service Download Page 26

Page: 26 / 75

RE220002 Rev. 6

Disassembly Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge capacitor(s)
before following any disassembly procedures.

WARNING

Component Module Panel Removal

(Model VEND-10.F, .G, .H, .J, VEND-10, VEND-11
1. Remove the control panel assembly.
2. Remove two interlock switch module screws and

remove the switch module. Do not disconnect wires
to the switch module.

3. Remove the nut at the top of the component module

panel. Pull the top of the panel away from the cavity
wall until it clears the stud.

4. Pull the component module panel toward the front of

the oven and lift up to separate the two tabs from
slots in the oven base.

5. Slowly pull the interlock switch module and

component module panel through the control panel
opening. Move wires around as required to clear the
opening.

NOTE: After replacement, perform interlock switch

module adjustment. Perform Radio Frequency
Leakage Test Procedures.

Stirrer Cover Removal

Stirrer Assembly Removal

NOTE: Formed washers were used on early production

only. Formed washers are not used with
replacement stirrer blades.

NOTE: If installed, formed washers must be installed as

shown.

NOTE: Check oven for leakage to ensure less than 4

mw/cm

leakage at 5 cm.

NOTE: Radio Frequency gasket must be installed as

shown.

Summary of Contents for A1200S












































































Search results

Summary of Contents for A1200S

Reviews:

Amana A1200S, Service, Page: 26 / 75

Search results

Summary of Contents for A1200S

Reviews: