manualshive.com logo in svg

Amana A1200S, Service, Page: 32 / 75

Share
Download
Amana A1200S Service Download Page 32

RE220002 Rev. 6`

32

Troubleshooting Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

Diagnosis for VEND-10.000, .A, .B, .C, FS-10EVP, FS-14, FSP-10

Test Sequence 3:  Vari-Power Condition

Open oven door, place a cup of cool water in 
oven, close door, push button one and note 
time in display, open door and program button 
one for one minute of defrost as described, 
push button one.

Oven starts and times down, cavity light
changes brillance and the oven sound 
varies in intensity (pulses) twice approximately 
every 12 seconds indicating vari-power 
operation, the water is warmed?

 

1.
2.

Oven operates on high only or 
does not heat at all.

Inoperative triac.
Inoperative controller

Vari-power  operation normal, reprogram 
button one to the time noted above, proceed 
to shutdown condition (Test Sequence 4).

Test Sequence 4:  Shutdown Condition

60 seconds after a cook cycle or door 
transition, all components shut off?

 1.

2.

Inoperative controller.
Inoperative holding relay.

3.

Broke or improper wire connection.

 

Oven operation is normal.

Yes

No

Yes

No

Summary of Contents for A1200S












































































Reviews:

No comments