manualshive.com logo in svg

Amana A1200S, Service, Page: 3 / 75

Share
Download
Amana A1200S Service Download Page 3

3

RE220002   Rev. 6

Table of Contents

IMPORTANT PRODUCT INFORMATION ........................................................................................................ 2

MODEL AND MANUFACTURING NUMBERS ................................................................................................. 4

IMPORTANT SAFETY INFORMATION ........................................................................................................... 6

IMPORTANT  PRODUCT  GROUNDING  AND OUTLET   INFORMATION ................................................... 7

SPECIFICATIONS ............................................................................................................................................ 9

CAUTIONS AND WARNINGS to be Observed During Disassembly and Troubleshooting ............................. 10

GENERAL INFORMATION AND OPERATING INSTRUCTIONS .................................................................... 11

TEST PROCEDURES ...................................................................................................................................... 13

DISASSEMBLY PROCEDURES ...................................................................................................................... 21

SERVICE INFORMATION ................................................................................................................................ 28

PROCEDURE FOR MEASURING MICROWAVE ENERGY LEAKAGE .......................................................... 29

TROUBLESHOOTING ..................................................................................................................................... 30

VEND-10, 11 PROGRAMMING INSTRUCTIONS ........................................................................................... 41

FS-10, 11, 14, 16 PROGRAMMING INSTRUCTIONS ..................................................................................... 45

FSP-10, 11 PROGRAMMING INSTRUCTIONS .............................................................................................. 48

A1200S, A1225S  PROGRAMMING INSTRUCTIONS .................................................................................... 50

SCROLLING MESSAGE PROCEDURE .......................................................................................................... 55

WIRING SCHEMATIC/DIAGRAM .................................................................................................................... 56

REPLACE MANUAL C-SM033 WITH THIS MANUAL, RE220002.

REV. 1—ADDED MODEL FSP10SS, P4020004103 TO MANUAL.  THIS MODEL IS SIMILAR TO MODEL

FSP10, P4020004102.

REV. 2—ADDED MODEL FSP11SS, P1185803M TO MANUAL.  THIS MODEL IS SIMILAR TO MODEL

FSP11, P1185802M.

REV. 3—ADDED MODEL VEND11B, P1185804M, P1302101M; FSP11SS, P1302102M; FSP11LW, P1302103M;

FSP11EVP, P1302104M; FS17EVP, P1302105M; AND FS20EVP, P1302106M TO MANUAL.

REV.4—ADDED MODELS FS17EVP, P1185902M; AND FS20EVP, P1185903M TO THIS MANUAL.

REV. 5—CORRECTED MODEL INDENTIFICATION FS17EVP TO FS17; FS20EVP TO FS20; FSP11EVP TO

FSP11; FS11SS TO FS11; AND VEND11B TO VEND 11 ALONG WITH ASSOCIATED TEXT. ADDED
FSP11LW, P1185805M.

REV. 6—CORRECTED MODELS ASSIGNED TO WIRING DIAGRAM, AND ADDED NEW CONTROLLER

TESTING PROCEDURE.

Summary of Contents for A1200S












































































Reviews:

No comments