manualshive.com logo in svg

Altera Arria V GZ, User Manual

The Altera Arria V GZ User Manual is now available for free download at manualshive.com, ensuring convenient access to essential instructions for this high-performance product. This comprehensive manual equips users with comprehensive details and troubleshooting guidance, enabling optimal utilization of the Altera Arria V GZ.

Share
Download
background image

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

User Guide

15.  Hard IP Reconfiguration and

Transceiver Reconfiguration

This chapter describes features of the Arria V GZ Hard IP for PCI Express that you can 
use to reconfigure the core after power-up. It includes the following sections:

■

Hard IP Reconfiguration Interface

■

Transceiver PHY IP Reconfiguration

Hard IP Reconfiguration Interface

The Arria V GZ Hard IP for PCI Express reconfiguration block allows you to 
dynamically change the value of configuration registers that are 

read-only

. You access 

this block using its Avalon-MM slave interface. For a complete description of the 
signals in this interface, refer to 

“Hard IP Reconfiguration Interface” on page 6–45

.

The Hard IP reconfiguration block provides access to 

read-only

 configuration registers, 

including Configuration Space, Link Configuration, MSI and MSI-X capabilities, 
Power Management, and Advanced Error Reporting (AER). 

The procedure to dynamically reprogram these registers includes the following three 
steps:

1. Bring down the PCI Express link by asserting the 

hip_reconfig_rst_n

 reset signal, 

if the link is already up. (Reconfiguration can occur before the link has been 
established.)

2. Reprogram configuration registers using the Avalon-MM slave Hard IP 

reconfiguration interface.

3. Release the 

npor

 reset signal.

1

You can use the LMI interface to change the values of configuration registers that are 

read/write

 at run time. For more information about the LMI interface, refer to 

“LMI 

Signals” on page 6–43

. 

Table 15–1

 lists all of the registers that you can update using the PCI Express 

reconfiguration block interface.

 

Table 15–1.  Dynamically Reconfigurable Registers in the Hard IP Implementation  (Part 1 of 8)

Address

Bits

Description

Default

Value

 Additional Information 

0x00

0

When 0, PCIe reconfig mode is enabled. When 1, PCIe 
reconfig mode is disabled and the original read only 
register values set in the programming file used to 
configure the device are restored. 

b’1

—

0x01-0x88

Reserved.

—

0x89

15:0 Vendor 

ID.

0x1172

Table 7–2 on page 7–2

, 

Table 7–3 on page 7–2

0x8A

15:0

Device ID.

0x0001

Table 7–2 on page 7–2

, 

Table 7–3 on page 7–2

November 2012
UG-01097-1.4

Summary of Contents for Arria V GZ













































































































































































































































































































Reviews:

No comments

Related manuals for Arria V GZ

Hama Gigabit Network Set Installation Instructions Manual preview
Gigabit Network Set
Brand: Hama Pages: 6
Kanguru FC-RW Quick Start Manual preview
FC-RW
Brand: Kanguru Pages: 1
Kantech KT-MUL-MT-KP Instruction Manual preview
KT-MUL-MT-KP
Brand: Kantech Pages: 2
FingerTec TimeLine 100 Quick Start Manual preview
TimeLine 100
Brand: FingerTec Pages: 4
ATI Technologies 9800PRO - 128MB Dell - Radeon AGP 8x Vga DVI Tv-out DDR X2603 Installation And Setup Manual preview
9800PRO - 128MB Dell - Radeon AGP 8x Vga DVI Tv-out DDR X2603
Brand: ATI Technologies Pages: 64
DFI LAX100 User Manual preview
LAX100
Brand: DFI Pages: 44
C Prox Quntek PN10 User Manual preview
Quntek PN10
Brand: C Prox Pages: 7
IEI Technology LAN-100G2SF-E810 Quick Installation Manual preview
LAN-100G2SF-E810
Brand: IEI Technology Pages: 5
AJA KONA 3 Installation And Operation Manual preview
KONA 3
Brand: AJA Pages: 82
Klark Teknik DN9824 Operator'S Manual preview
DN9824
Brand: Klark Teknik Pages: 36
Hauppauge Colossus 2 Quick Installation Manual preview
Colossus 2
Brand: Hauppauge Pages: 2
Diamond Multimedia Radeon X1300PCI Specification Sheet preview
Radeon X1300PCI
Brand: Diamond Multimedia Pages: 1
Eizo Raptor DL–Lite Brochure preview
Raptor DL–Lite
Brand: Eizo Pages: 2
TwinMOS CRW7A3 Quick Installation Manual preview
CRW7A3
Brand: TwinMOS Pages: 2
Cisco Linksys Wireless-B Quick Installation Manual preview
Linksys Wireless-B
Brand: Cisco Pages: 62
Cisco Linksys LNE100TX User Manual preview
Linksys LNE100TX
Brand: Cisco Pages: 85
IFM Electronic DTE800 Operating Instructions Manual preview
DTE800
Brand: IFM Electronic Pages: 37
EMS Imaging XtremeRGB-Ex1+ User Manual preview
XtremeRGB-Ex1+
Brand: EMS Imaging Pages: 9

Brands by name

Popular brands

Load more brands