Altera Arria V GZ User Manual Download | Manualshive

Page: 139 / 300

background image

Chapter 6: IP Core Interfaces

6–45

Hard IP Reconfiguration Interface

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

describes the signals that comprise the LMI interface.

LMI Read Operation

illustrates the read operation.

LMI Write Operation

illustrates the LMI write. Only writeable configuration bits are

overwritten by this operation. Read-only bits are not affected. LMI write operations
are not recommended for use during normal operation with the exception of AER
header logging.

Hard IP Reconfiguration Interface

The Hard IP reconfiguration interface is consists of an Avalon-MM slave interface
with a 10-bit address and 16-bit data. You can use this bus dynamically modify the
value of configuration registers that are read-only at run time. To ensure proper
system operation, Altera recommends that you reset or repeat device enumeration of
the PCI Express link after changing the value of read-only configuration registers of
the Hard IP. For a description of the registers available via this interface refer to

Chapter 15, Hard IP Reconfiguration and Transceiver Reconfiguration

.

Table 6–20. LMI Interface

Signal

Width

Dir

Description

lmi_dout

32

O

Data outputs

lmi_rden

1

I

Read enable input

lmi_wren

1

I

Write enable input

lmi_ack

1

O

Write execution done/read data valid

lmi_addr

12

I

Address inputs, [1:0] not used

lmi_din

32

I

Data inputs

Figure 6–35. LMI Read

pld_clk

lmi_rden

lmi_addr[11:0]

lmi_dout[31:0]

lmi_ack

Figure 6–36. LMI Write

pld_clk

lmi_wren

lmi_din[31:0]

lmi_addr[11:0]

lmi_ack

«
...
137
138
139
140
141
...
»

Summary of Contents for Arria V GZ













































































































































































































































































































Reviews:

No comments

Related manuals for Arria V GZ

Montego II Quadzilla

Brand: Voyetra Turtle Beach Pages: 56

Brand: Racelogic Pages: 2

Brand: Renkforce Pages: 2

ViVOpay KioskII

Brand: IDTECH Pages: 19

FZ-VSC552 Series

Brand: Panasonic Pages: 6

FZ-VSC551 Series

Brand: Panasonic Pages: 8

Brand: Riverbed Pages: 154

Brand: HID Pages: 2

Technology Solutions 1139

Brand: HID Pages: 16

Brand: BITMAIN Pages: 7

Brand: BBPOS Pages: 2

Brand: Connect Tech Pages: 16

Brand: Tecknet Pages: 4

Brand: PAX Pages: 18

Brand: Intersil Pages: 10

Brand: Renkforce Pages: 4

Brand: Diablotek Pages: 1

Brand: Manhattan Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands