ITA
ENG
FRA
ESP
DEU
POR
6-1624050 rev.12 14/11/2012 Pag 9 di 9
4. Put in function and maintenance
Warning: the following notes are exclusively addressed to qualified personnel.
4.1 Put in function of the automation
For the put in function of the automation it is necessary to execute the programming of the electronic panel inserted
on the board of the motor.
This sort of programming must be executed only by qualified personnel after having finished and checked the
installation of the mechanical part of the automation on each of his point.
Particularly the following points must be always checked:
•
The correct balancing of the door. By positioning the door open at 60-70 cm. from the ground, it must neither
open nor close by itself.
•
The sliding of all the movable parts. The door must execute a fluid movement.
•
The correct functioning of the unlocking device in each position of the door.
•
The lubrication, if necessary, of the mechanical parts of the door.
Before executing the wirings necessary to the functioning of the automation, read the following warnings:
•
Some points of the system are subjected to dangerous tensions. For this reason, the installation, the opening
and the programming of the panel must be executed only by qualified personnel. All the operations that the final
user can execute do not require the opening of the box.
•
Provide the use of a means which assures the omni polar disconnection from the power supply of the system. It
can be either an omni polar switch (directly connected to the terminals of the power supply) with a minimal
distance of the contacts of 3 mm. on each pole, or an issue integrated in the power supply net.
•
For the connection to the power supply, use flexible cables with CENELEC H05W designation and anyway with
minimal section of the single conductor not inferior to 0,75 mm².
•
It is advisable to check the absorptions of all the devices connected to the outputs of the control unit, like for
example luminous spies, photocells, safety devices, etc., in a way to re-enter in the limits indicated on the table
of the technical data. The correct functioning of the product in case of inobservance of these limitations is not
guarantee.
•
The constructor declines all responsibilities in case of inobservance of these cautions.
4.2 Maintenance of the automation
It is advisable to make periodically check the automation by specialized technical personnel.
To assure a correct functioning of the automation, it is necessary to observe the following points:
•
Check regularly the balancing of the door. The door must be easily manoeuvrable by hand in an easy way, for
this purpose unlock the slide and with the due cautions move manually in opening and in closing bringing it on
the anchorage point of the steel to the door self. The force necessary to do this action must not exceed the 15
Kg.
•
The door and particularly the cables, the springs and the fixing components must be regularly checked to
ensure that they do not show signs of wear, of damage or of unbalancing .
•
The anti-squashing control must be periodically checked. If it is necessary, correct the regulation of the
reversing function and check again the functioning. Make reference to the instructions of the CT ACTION
(code: 6-1622345) / GAR.AS (code: 6-1622375) for sectional door.
The substitution of the bulb must be executed exclusively by qualified personnel. For the substitution proceed as
follows:
1.Cut off the power supply to the system.
2.Unscrew the screws which fix the cover in his seat.
3.Remove the cover
4.Push and rotate the bulb in clockwise sense until you can remove her.
5.Replace the bulb with one of the same characteristics.
GUARANTEE - In compliance with legislation, the manufacturer’s guarantee is valid from the date stamped on the product and is restricted to the
repair or free replacement of the parts accepted by the manufacturer as being defective due to poor quality materials or manufacturing defects.
The guarantee does not cover damage or defects caused by external agents, faulty maintenance, overloading, natural wear and tear, choice of
incorrect product, assembly errors, or any other cause not imputable to the manufacturer. Products that have been misused will not be guaranteed
or repaired.
Printed specifications are only indicative. The manufacturer does not accept any responsibility for range reductions or malfunctions caused by envi-
ronmental interference. The manufacturer’s responsibility for damage caused to persons resulting from accidents of any nature caused by our de-
fective products, are only those responsibilities that come under Italian law.
