manualshive.com logo in svg

Allied Hy-Ram HR270, Safety, Operation And Maintenance Instructions, Page: 43 / 60

Share
Download
Allied Hy-Ram HR270 Safety, Operation And Maintenance Instructions Download Page 43

Allied Construction Products, LLC www.alliedcp.com 

SOMM577202_14mar 

32

10.0 Changing the Tool – [cont’d] 

 

 

Fig 10-7 Stand Upright. Push Tool Against Firm 

Surface. OK To Grease 

 

 

Fig 10-8 Tool Seated Against Thrust Ring Prevents 

Bypass Into Impact Chamber 

 

Conventional re-lubrication is accomplished with a 
grease dispenser such as a standard hand-operated 
or power-assisted grease gun.  
 
Apply lubricant as shown in Fig. 10-6. The top lube 
fitting lubricates the upper bushing. The lower 
bushing is lubricated through the bottom fitting.  
 
1.  On stable and level ground, stand the breaker 

vertically and push the tool firmly against the 
ground. Engage interlock and shut off carrier. 

 
2.  Wipe off grease nipple. Press grease gun over 

top lubrication nipple. Pump lever 20-30* strokes. 

 
3.  Repeat step 2 on lower lube nipple. 
 
*The amount a grease gun will deliver per lever 
stroke will vary widely from one gun to the next. The 
amount dispensed must equal the amount consumed 
between last replenishment. If greasing intervals are 
infrequent, additional strokes will be necessary to 
refill grease reserves. Pump enough grease until 
surfaces are sufficiently covered.  
 

Generally, tool re-lubrication is recommended every 
two hours. However, the operator must actively 
monitor the tool and grease must always visible. If 
not, shorten the time between re-lubrication. Excess 
lubrication ends up as waste. Either extend period 
between re-lubrication or decrease the number of 
lever strokes. 
 

 

 

Fig 10-9 Grease Must Be Visible On Tool At All 

Times 

 

10.4.1 Avoid Costly Lubrication Mistakes 

 

CAUTION

 

At no time is it permissible to re-lubricate 
the tool with the breaker lying horizontally 
as shown in Figure 10-9. Neglecting to 
press the tool against thrust ring will allow 
grease to by-pass and fill the space above 
the tool (impact chamber).  

If this occurs, the oil seals may be dislodged and lead 
to piston and cylinder damage.  

 

 

 

 

 

Fig 10-10 Incorrect Re-Lubrication Position 

 

Summary of Contents for Hy-Ram HR270





























































Reviews:

No comments