Allied Telesis AT-9400 User Manual Download | Manualshive

Page: 116 / 668

background image

Chapter 6: Static Port Trunks

116

Section I: Basic Operations

Creating a Static Port Trunk

This section contains the procedure for creating a static port trunk on a
switch.

Caution

Do not connect the cables to the trunk ports on the switches until
after you have configured the trunk with the management software.
Connecting the cables before configuring the software will create a
loop in your network topology. Data loops can result in broadcast
storms and poor network performance.

Note

Before creating a port trunk, examine the speed, duplex mode, and
flow control settings of the lowest numbered port that will be a part of
the trunk. Check to be sure that the settings are correct for the end
node to which the trunk will be connected. When you create the
trunk, the AT-S63 Management Software copies the settings of the
lowest numbered port in the trunk to the other ports so that all the
settings are the same.

You should also check to be sure that the ports are untagged
members of the same VLAN. You cannot create a trunk of ports that
are untagged members of different VLANs.

To create a port trunk, perform the following procedure:

1. From the Main Menu, type

1

to select Port Configuration.

2. From the Port Configuration menu, type

4

to select Port Trunking and

LACP

.

The Port Trunking and LACP menu is shown in Figure 35.

Figure 35. Port Trunking and LACP Menu

Allied Telesis AT-9448T/SP - AT-S63

Marketing

User: Manager

11:20:02 02-Mar-2005

Port Trunking and LACP

1 - Static Port Trunking
2 - LACP Configuration

R - Return to Previous Menu

Enter your selection?

«
...
114
115
116
117
118
...
»

Summary of Contents for AT-9400





























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-9400

Brand: Canon Pages: 153

Brand: Canon Pages: 132

Brand: Canon Pages: 135

Brand: Canon Pages: 198

Brand: Canon Pages: 98

RS232 interface for GT47 embedded apps UART

Brand: Sony Ericsson Pages: 14

ZENworks Network Access Control 5.0

Brand: Novell Pages: 534

ADVANCED SERVER

Brand: ACRONIS Pages: 2

Unity Express 8.0 Voice-Mail System

Brand: Cisco Pages: 50

TELEPRESENCE MANAGEMENT SUITE PROVISIONING

Brand: Cisco Pages: 16

Unified MeetingPlace H.323/SIP

Brand: Cisco Pages: 54

PVDM2 24DM - Digital Modem Module

Brand: Cisco Pages: 48

TELEPRESENCE MANAGEMENT SUITE SECURE SERVER

Brand: Cisco Pages: 34

Brand: Cisco Pages: 8

Unified Videoconferencing Manager

Brand: Cisco Pages: 22

SMART BUSINESS COMMUNICATIONS SYSTEM

Brand: Cisco Pages: 27

MDS 9222i - Multiservice Modular Fabric Switch

Brand: Cisco Pages: 40

MCS 7825 Series

Brand: Cisco Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands