44
53264
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
TO REMOVE BAFFLES
a. Remove screws and washers (if present)
holding baffles to cylinder. Refer to Figure 36.
61. REAR SEAL
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove two cabinet top hold-down screws.
Refer to Figure 26.
c. Lift front of cabinet top and disengage from
hinges on rear of cabinet. Refer to Figure 27.
NOTE: Cabinet top may be raised and hinged on
the rear hold-down brackets, or supported against
wall behind the dryer.
IMPORTANT: When installing seal, tape it to the
bulkhead in several places to hold in position while
replacing seal strap and spring. Remove tape after
strap and spring are in place. Seal must be under
strap securely and be folded under flanged edge
around entire bulkhead. Strap must be installed
with cupped surface down against the seal to hold
the felt seal more firmly in place on the bulkhead.
Also, the seal can be adhered to the bulkhead using
3M-1300 Sealant (obtain locally). This is
accomplished by applying a bead of 3M-1300
Sealant around the entire flanged area where the
felt seal contacts the bulkhead.
62. CYLINDER ROLLERS AND ROLLER
SHAFT
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove cylinder assembly. Refer to Paragraph
60, steps “b” through “e”.
c. Refer to Figure 38 for removal of roller from
roller shaft.
Figure 36
DRY863S
BAFFLE
CYLINDER
WASHER
(if present)
HEX HEAD
SCREW
Figure 37
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
@@@@@@@@@
@@@@@@@@@
@@@@@@@@@
@@@@@@@@@
@@@@@@@@@
@@@@@@@@@
@@@@@@@@@
@@@@@@@@@
@@@@@@@@@
@@@@@@@@@
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
;;;;;;;;;
QQQQQQQQQ
QQQQQQQQQ
QQQQQQQQQ
QQQQQQQQQ
QQQQQQQQQ
QQQQQQQQQ
QQQQQQQQQ
QQQQQQQQQ
QQQQQQQQQ
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
¢¢¢¢¢¢¢¢¢
DRY864S
;;
;;
;;
;;
@@
@@
@@
@@
ÀÀ
ÀÀ
ÀÀ
ÀÀ
;;
;;
;;
;;
¢¢
¢¢
¢¢
¢¢
HEX HEAD
SCREW
HEAT
SHIELD
CYLINDER
ROLLERS
SPRING
SEAL
STRAP
PHILLIPS HEAD
SCREWS
