manualshive.com logo in svg

Alcatel-Lucent 1643 AM, Operation Manual, Page: 103 / 386

Share
Download
Alcatel-Lucent 1643 AM Operation Manual Download Page 103

Maximum number of VLAN instances exceeded in MIB

...................................................................................................................................................................................................................................

Alarm identifier

MIBcVLANOVFW

Information

The maximum number of VLAN instances that can be stored in the
management information base (MIB) has been exceeded.

Alarm category

Transmission

ASAP

ethPath

Alarm severity
(default setting)

Information

Reporting state
(default setting)

Reported

Local indications

The red fault LED is lit.

Cause

Too many VLAN instances per network element or too many VLAN/port
associations have been created.

Actions

Remove unused VLAN instances and re-plan the network to decrease the
number of VLAN instances.

Note(s)

A maximum number of 1024 VLAN instances per network element is
supported.

A maximum number of 2000 VLAN/port associations is supported.

Alarm messages

...................................................................................................................................................................................................................................

365-312-803R7.2
Issue 4, May 2007

Alcatel-Lucent - Proprietary

See notice on first page

1-83

Summary of Contents for 1643 AM



































































































































































































































































































































































































Reviews:

No comments