AL-KO MS 2600, Instruction Manual

Page: 21 / 304

21
GB
474 698_a
Startup MS 2600 / MS 3300 L
Cold start (Fig. 6) (Fig. 9)
6-1 Air filter shroud
6-2 Petrol tank
6-3 “Choke” – “Run” choke
6-4 Primer (cold-start diaphragm pump)
6-5 Starter cord
9-1 “Start” – “Stop” ignition switch
9-2 Gas lever lock
9-3 Gas lever
1. Set the ignition switch to the “Start” position (9-1).
2. Press the gas lever lock (9-2) and hold it down; press
the gas lever (9-3).
3. Set the choke (6-3) to the “CHOKE” position.
4. Press cold-start diaphragm pump (6-4) 10 times.
5. Pull the starter cord (6-5) straight out 3-4 times until
the engine audibly starts briefly (ignition).
Pull the cord briskly with uniform force.
6. Set the choke to “RUN”.
7. Pull out the starter cord until the engine starts.
8. If the engine does not start, repeat steps 1 to 7.
MS 2600 / MS 3300 L warm start (Fig. 6) (Fig. 9)
1. Set the ignition switch to the “Start” position (9-1).
2. Set the choke (6-3) to “RUN”. Pull the starter cord
(6-5) – the engine starts.
„
Engine does not start:
„
Set the choke to the “RUN” position.
„
Pull the starter cord 5 times.
„
If the engine still does not start:
„
Wait 5 minutes and then try again with the gas
lever pressed down.
Refer to the “Troubleshooting” chapter.
Switching off the engine (Fig. 9)
1. Release the gas lever and let the engine idle.
2. Set the ignition switch (9-1) to “STOP”.
Caution!
The engine and cutting equipment continue to run after
being switched off – Risk of injury!
Startup MS 3300 B / MS 4300
Cold start (Fig. 6) (Fig. 13)
6-1 Air filter shroud
6-2 Petrol tank
6-3 “Choke” – “Run” choke
6-4 Primer (cold-start diaphragm pump)
6-5 Starter cord
13-1 “Start” – “Stop” ignition switch
13-2 Gas lever lock
13-3 Gas lever
1. Set the choke (6-3) to the “CHOKE” position.
2. Set the ignition switch to the “Start” position (13-1).
3. Press cold-start diaphragm pump (6-4) 10 times.
4. Pull the starter cord (6-5) straight out 2-3 times until
the engine audibly starts briefly (ignition).
Pull the cord briskly with uniform force.
5. Set the choke to “RUN”.
6. Pull out the starter cord until the engine starts.
7. If the engine does not start, repeat steps 1 to 7.
MS 3300 B / MS 4300 warm start (Fig. 6) (Fig. 13)
1. Set the ignition switch to the “Start” position (13-1).
2. Set the choke (6-3) to the “RUN” position.
3. Pull the starter cord (6-5) a maximum of 6 times – the
engine starts. Keep the gas lever pressed down until
the engine runs smoothly.
„
Engine does not start:
„
Set the choke to the “RUN” position.
„
Pull the starter cord 5 times.
„
If the engine still does not start:
„
Wait 5 minutes and then try again with the gas
lever pressed down.
Refer to the “Troubleshooting” chapter.
Switching off the engine (Fig. 13)
1. Release the gas lever (13-3) and let the engine idle.
2. Set the ignition switch (13-1) to “STOP”.
Caution!
The engine and cutting equipment continue to run after
being switched off – Risk of injury!