background image

Purging the Heating Loop

©Aqua-Hot®

 600D Installation Manual 

p. 43

Winterizing the Aqua-Hot

The  Aqua-Hot’s  domestic  water  heating  system  must  be 

completely drained of domestic water at any time the heater is 
stored where freezing temperatures may be experienced.

Please follow these instructions when winterizing the Aqua-

Hot domestic water heating system. Reference Figure 87 for a 
system overview.

1.  Completely drain the fresh water storage tank.
2.  Disconnect the domestic water demand pump suction line 

from the fresh water storage tank.

3.  Attach an adequate piece of hose onto the suction side of 

the domestic water demand pump.

4.  Place the opposite end of the hose into an adequate supply 

of  non-toxic  RV  winterization  antifreeze  (FDA  certifi ed  as 
“GRAS” Generally Recognized As Safe must be used) and 
allow the fl uid to pump through.

5.  Open and close all interior and exterior water faucets one 

at a time, until ONLY pure RV antifreeze is present. Perform 
this procedure for both cold and hot water faucets.

6.  Remove  the  hose  and  reconnect  the  domestic  water 

demand  pump’s  suction  line  to  the  fresh  water  storage 
tank.

Winterizing the Aqua-Hot

Not  winterizing  the  Aqua-Hot  when  freezing  temperatures 
are present will result in SERIOUS damage to the Aqua-Hot 
domestic water heating system. Ensure that only non-toxic 
RV  antifreeze  (FDA  approved  “GRAS”  antifreeze)  rated  for 
winterization is used when winterizing this unit. The warranty 
does not cover freeze damage.

NOTE: 

The Aqua-Hot can continue to be used for interior heat 

once  the  domestic  hot  water  system  has  been  winterized.

De-Winterization

To de-winterize the Aqua-Hot system, completely fi ll the fresh 

water  storage  tank.  Open  and  close  the  interior  and  exterior 
faucets, one at a time, until only clear water is present.

Disinfecting the Domestic Water System

The Aqua-Hot Heating systems contain copper tubing and are 

not compatible to prolonged exposure to sodium  hypochlorite 
(bleach  or  liquid  bleach).  Using  products  containing  bleach, 
including water refreshers, may cause corrosion of the domestic 
water lines, resulting in a catastrophic failure of the Aqua-Hot 
system by creating leaks that cannot be repaired. This damage 
is not covered by the Aqua-Hot warranty.

If disinfecting the hot water system, be sure to follow NFPA 

1192  Standard  on  Recreational  Vehicles  “Instructions  for 
Disinfection of Potable Water Systems” or any other applicable 
local standards for Potable Water Systems.

NOTE: 

Extended  exposure  to  household  bleach  will  corrode  the 

components  of  the  Aqua-Hot  will  potentially  dramatically  shorten 
the operational lifetime of the Aqua-Hot. Under no circumstances 
is  the  Aqua-Hot  to be exposed to  household  bleach  for  extended 
periods of time.

To Hot Water Faucets

Tempered

Domestic Hot Water

Fresh Water 

Storage Tank

 Cold Water Faucets

Demand Pump

Figure 87

AT

AT

Indicates options for mounting 

an Accumulator Tank.

AT

AT

Summary of Contents for Aqua-Hot 600 Series
































































Reviews: