manualshive.com logo in svg

AirLive SNMP-FSH2602MG V2, User Manual, Page: 36 / 139

Share
Download
AirLive SNMP-FSH2602MG V2 User Manual Download Page 36

4.  Web Management in SNMP-FSH2602MG v2 

 

 

 

31 

AirLive SNMP-FSH2602MG v2 User’s Manual

 

 

 
 

4.4.5.3 State Activity 

 
When setup the LACP aggregator, you can configure port state activity. You can mark or 
un-mark the port. When you mark the port and click “

Apply

” button, the port state activity 

will change to 

Active

. Opposite is 

Passive

. 

 
1. 

Active: 

The port automatically sends LACP protocol packets. 

2. 

Passive: 

The port does not automatically send LACP protocol packets, and responds 

only if it receives LACP protocol packets from the opposite device. 

Note: 

„

  A link having either two active LACP ports or one active port can perform dynamic 

LACP trunking. 

„

  A link having two passive LACP ports will not perform dynamic LACP trunking 

because both ports are waiting for LACP protocol packet from the opposite device. 

„

  If you are active LACP’s actor, when you are selecting trunking port, the active 

status will be created automatically. 

 

 

Summary of Contents for SNMP-FSH2602MG V2












































































































































Reviews:

No comments