AirLive SNMP-FSH2602MG V2 User Manual Download Page 132

Page: 132 / 139

9. Specifications

127

AirLive SNMP-FSH2602MG v2 User’s Manual

System memory

8Mbytes

LED

System

power

10/100Base-TX: Link/Activity, Full Duplex/Collision

1000Base-T: 100, 1000, Link/Activity, Full

Duplex/Collision

Management

Telnet/ Web/ SNMP v1 management, RS-232 console

management

RFC

Standard

RFC 1157 SNMP, RFC 1213 MIB II, RFC 1643

Ethernet like, RFC 1493 Bridge MIB, RFC 1757
RMON 1, RFC 1215 Trap, RFC 2674 VLAN MIB,
private MIB

SNMP

Trap

Cold start, link down, link up, authorization fail.

Trap station up to 3.

TFTP and Console firmware upgradeable

Port

Trunk

Support IEEE802.3ad with LACP function.

Up to 7 trunk groups and group member up to 4.

Trunk port within 24-port 10/100TX and 2 Ext.

Gigabit port

Supports IEEE802.1d STP & IEEE802.1w RSTP

VLAN

Port based VLAN

IEEE802.1Q

Tag

VLAN

GVRP

IEEE802.1v Protocol VLAN (IP, IPX,..)

Static VLAN groups up to 256, Dynamic VLAN

group up to 2048, VLAN ID from 0 to 4094

QoS policy: Supports 8 priority levels ID for two priority

queue

Class of Service

Summary of Contents for SNMP-FSH2602MG V2












































































































































Search results

Summary of Contents for SNMP-FSH2602MG V2

Reviews:

AirLive SNMP-FSH2602MG V2, User Manual, Page: 132 / 139

Search results

Summary of Contents for SNMP-FSH2602MG V2

Reviews: