manualshive.com logo in svg

AirLive SNMP-FSH2602MG V2, User Manual, Page: 16 / 139

Share
Download
AirLive SNMP-FSH2602MG V2 User Manual Download Page 16

3.  Configuring the SNMP-FSH2602MG v2 

 

 

 

11 

AirLive SNMP-FSH2602MG v2 User’s Manual

 

2. 

Set your PC’s IP address manually to 192.168.10.100 (or other address in the same 
subnet) 

 

 

You are ready now to configure the SNMP-FSH2602MG v2 by using your PC.     
 
 

3.3 Management Interface 

The SNMP-FSH2602MG v2 can be configured using on the management interfaces below: 
 

„

 

Web Management (HTTP)

: You can manage your SNMP-FSH2602MG v2 by simply 

typing its IP address in the web browser. Most functions of SNMP-FSH2602MG v2 can 
be accessed by web management inter face. We recommend using this interface for 
initial configurations. To begin, simply enter SNMP-FSH2602MG v2’s IP address 
(default is 192.168.10.1) on the web browser. The default username and password are 

airlive

. 

 

„

 

Console Management (Terminal)

: SNMP-FSH2602MG v2 can be managed through 

terminal emulation program or 

Hyper Terminal

.  

 
When the connection between SNMP-FSH2602MG v2 and PC is ready, turn on the PC 
and run a terminal emulation program or Hyper Terminal and configure its 
communication parameters to match the following default characteristics of the 
console port 
 

Summary of Contents for SNMP-FSH2602MG V2












































































































































Reviews:

No comments