manualshive.com logo in svg

AirLive SNMP-FSH2602MG V2, User Manual, Page: 14 / 139

Share
Download
AirLive SNMP-FSH2602MG V2 User Manual Download Page 14

2. Installing the SNMP-FSH2602MG v2 

 

 

9 

AirLive SNMP-FSH2602MG v2 User’s Manual

 

Green

 

The port is connecting with the device.

 

Blink

 

The port is receiving or transmitting data.

 

LNK/ACT

 

Off 

No device attached.

 

Orange

 

The port is operating in Full-duplex mode.

 

FDX

 

Off 

In half-duplex mode

 

1000(Giga port) 
#25, #26 port

 

Green

 

In 1000Mbps connection speed

 

100(Giga port) 
#25, #26 port

 

Orange

 

In 100Mbps connection speed

 

Green

 

The port is connecting with the device.

 

Blink

 

The port is receiving or transmitting data.

 

LNK/ACT (Giga port) 
#25, #26 port

 

Off

 

No device attached

 

Orange

 

The port is operating in Full-duplex mode.

 

Blink

 

Collision of Packets occurs in the port.

 

FDX/COL (Giga port) 
#25, #26 port

 

Off

 

In half-duplex mode

 

 
 

Summary of Contents for SNMP-FSH2602MG V2












































































































































Reviews:

No comments