Aimco AcraDyne AB-CTA Operating Instructions Manual Download Page 2

Page: 2 / 36

- 2 -

1. IMPORTANT INFORMATION

2. GENERAL INFORMATION

2.1.0. Importance of the operating instructions . . . . . . . . . . . . . . . . . 6

2.2.0. Proper intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3.0. Improper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4.0. Guarantee and liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3. BASIC SAFETY INSTRUCTIONS

3.1.0. Notices in the operating instructions . . . . . . . . . . . . . . . . . . . . 9

3.2.0. Operator‘s responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2.1. Personnel‘s responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2.2. Personnel training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3.0. Risks when working with the tool . . . . . . . . . . . . . . . . . . . . . . 9

3.4.0. Danger from electrical energy . . . . . . . . . . . . . . . . . . . . . . . 10

3.4.1. Fundamental safety measures . . . . . . . . . . . . . . . . . . . . . . . 10

3.4.1. Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.4.2. Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.4.3. Personal safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4.4. Using and handling the power tool . . . . . . . . . . . . . . . . . . . . 11

3.4.5. Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.5.0. Lithium-ion battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.6.0. Cleaning and disposing of the tool . . . . . . . . . . . . . . . . . . . . 14

3.7.0. Risk of injury and damage to the tool . . . . . . . . . . . . . . . . . . . 14

4. START-UP

4.1.0. Installing or removing the battery . . . . . . . . . . . . . . . . . . . . . 15

4.1.1. Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.1.2. Rotating direction switch. . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.1.3. LED / Barcode scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.1.4. Multi-color LED control light . . . . . . . . . . . . . . . . . . . . . . . . 17

4.2.0. Setting the tightening torque. . . . . . . . . . . . . . . . . . . . . . . . 18

4.3.0. Cancel job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.4.0. Back-up strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.5.0. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5. DISPLAY

5.1.0. Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6. ACCESSORIES

7. TECHNICAL DATA

7.1.0. CTA Model Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 30

7.2.0. MTA Model Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 32

7.3.0. MCA Model Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 34

TABLE OF CONTENTS

Summary of Contents for AcraDyne AB-CTA





































Search results

Summary of Contents for AcraDyne AB-CTA

Reviews:

Related manuals for AcraDyne AB-CTA

Brands by name

Popular brands

Aimco AcraDyne AB-CTA, Operating Instructions Manual

Search results

Summary of Contents for AcraDyne AB-CTA

Reviews:

Related manuals for AcraDyne AB-CTA

Brands by name

Popular brands