Agilent Technologies 1664A Service Manual Download Page 132

Page: 132 / 164

To remove and replace the fan

Using previous procedures, remove the following assemblies:

•

Handle

•

Rear Feet

•

Cover

•

Disk Drive

•

Power Supply

•

Rear Panel

Disconnect the fan cable from the main circuit board.

Remove the four fan screws.

Lift the fan away from the rear panel.

Lift the fan guard away from the rear panel.

Reverse this procedure to install the fan.

When installing the fan, verify the correct orientation of the fan. If you mount the fan
backwards, the instrument will overheat. Also, check the correct polarity of the fan cable.

To remove and replace the line filter

Using previous procedures, remove the following assemblies:

•

Handle

•

Rear Feet

•

Cover

•

Disk Drive

•

Power Supply

•

Rear Panel

Unsolder the ground wire from the lug on the rear panel.

Disconnect the line filter cable from the power supply.

Remove the two screws attaching the line filter to the rear panel.

Slide the line filter assembly out toward the rear.

Reverse this procedure to install the line filter.

Replacing Assemblies

To remove and replace the fan

6–12

Summary of Contents for 1664A





































































































































































Search results

Summary of Contents for 1664A

Reviews:

Related manuals for 1664A

Brands by name

Popular brands

Agilent Technologies 1664A, Service Manual

Search results

Summary of Contents for 1664A

Reviews:

Related manuals for 1664A

Brands by name

Popular brands