7
(4)
Φ
3.5x5mm brass swage tubes
(2) 4-40 R/C Clevises with spring
(4) 4-40 solder coupler with nuts
(2) 4-40 Ball Links
(2) 4-40x16mm hex head bolts
(2) 4-40 lock nuts
(2)
Φ
3mm flat washers
(2) Brass Spacers
# 8
(1) Plastic Quick Link
(2) Wooden Rod Supports
(1) M2x300mm one end threaded rod
(1) M2 R/C Quick Link
(1) M2x20mm Threaded Rod
(1) 12” Flex Rod with Outer Case
(1) Throttle Servo Tray
# 9
(1)Wooden Mounting Block – For 30cc
DLE Gas Engine
(4) 8-32 x 20mm Hex Head Bolts
(4) 4mm Split Ring Flat Washer
(4) 4mm Flat Washer
(2) 1.20 size engine mounts, 1 left, 1 right
(4) 8-32x35mm hex head bolts for engine
mounts mounting
(4) 4mm flat washers for engine mounts
mounting
(4) 4mm split ring lock washers for
engine mounts mounting
(4) 8-32x30mm hex head bolts for engine
mounting
(4) 8-32 lock nuts for engine mounting
(4) 4mm flat washers for engine
mounting
(4) 4mm split ring lock washers for
engine mounting
(2) Hardwood Thrust Blocks for 2
stroke engine – marked with TOP
or BOTTOM
(2) Hardwood Thrust Blocks for 4
stroke engine – marked with L or R
# 10
(1) 750cc Fuel Tank with Rubber
Stopper (Glow/Gas)
(6) Small Nylon Ties
(2) Fuel Filler Dots
(3) Large Fuel Tubes
(1) 2 feet Large Glow Fuel Line (I.D.
3mm O.D. 5.7mm)
(2) Large Glow Fuel Line for inside
for Tank
(2) Fuel Clunks for inside of Tank
(1) Balsa Tri-stock for behind Fuel
Tank
# 11
(1) Tail Cone
(4) T2.6x12mm PWA Mounting
Screws
# 12
(1) Dash Panel Support - painted
(1) Dash Panel - painted
(1) Pilot Seat
(2) Steering Yokes
(2) Silicon Tubes
(2) Cotter Pins
(1) Felt Lined Cockpit sides
(6) T2.6x8mm PWA screws
# 13
(2) Antennas for the top of the wing
(1) Air Speed Tubes – paint white
# 14
(3) Switch Mounting Trays
(1) Battery Mounting Tray with 4 Holes
and 2 slots
(4) T2.6x8mm PWA screws for battery
mounting tray
(1) 6x100x60mm foam for fuel tank
(2) 8x80x300mm Sponge for receiver
and battery
(4) 356x12.5mm Velcro
(6) 5x500mm Nylon Ties for fuel tank
mounting
(1) Card Stock (8x12”) for the template
for cutting of cowling
(1) Rubber Grommets – 2 each
6,8,10
for fuel line and wire guide
# 15
(1) Custom Throw Meter
# 16
(1) C.G. Buddy
# 17
(1) Aluminum Spinner
# 18
(1) 300x300mm Silver covering
(1) 300x300mm Cub Yellow covering
(1) 300x300mm True Red covering
# 19
(4) Flap and Aileron Servo Hatch Covers
(8) Servo Mounting Hardwood Blocks
(24) T2.6x10mm PWA screws for Servo
Hatch and Mounting Blocks
(2) 8-32x25mm Hex Head bolts for wing
mounting
(2) #8 bonded washers
(2) Cotter Pins Rear
(1) 23x19.4x780mm Carbon/Fiberglass
compound wing tube
# 20 (1) Manual CD
