Aerotech Automation1 XC2 Hardware Manual Download Page 91

Page: 91 / 96

Index

-EB1

Analog Input

Analog Outputs

Auxiliary Encoder Input

Digital Inputs

68,71

Digital Outputs

68,73

I/O Option Board

Position Synchronized Output (PSO) Interface

-MX1

2014/30/EU

2014/35/EU

Absolute Encoder (Feedback Connector)

Absolute Encoder Schematic (Feedback Connector)

Agency Approvals

Altitude

Ambient Temperature

Analog Encoder (Feedback Connector)

Analog Encoder Phasing Reference Diagram

Analog Encoder Schematic (Feedback Connector)

Analog Encoder Specifications (Feedback Connector)

Analog I/O (AI/O) Connector [-EB1] Mating Connector Part

Numbers

Analog I/O (AI/O) Connector Pinout [-EB1]

Analog Input [-EB1]

Analog Input Pins (Analog I/O Connector [-EB1])

Analog Input Typical Connection [-EB1]

Analog Output Pins (Analog I/O Connector [-EB1])

Analog Output Specifications [-EB1]

Analog Output Typical Connection [-EB1]

Analog Outputs [-EB1]

AUX Connector Mating Connector Part Numbers

AUX Connector Pinout

Auxiliary Encoder Connector Pinout

Auxiliary Encoder Input [-EB1]

BiSS absolute encoder

Brake Connected to the Feedback Connector

Brake Control Relay Specifications

Brake Output Pins on the Feedback Connector

Brake Outputs (Feedback Connector)

Brushless Motor Configuration (Motor Power Output

Connector)

Brushless Motor Connections (Motor Power Output

Connector)

Brushless Motor Phasing Goal

Brushless Motor Phasing Oscilloscope Example

Brushless Motor Powered Motor Phasing

Brushless Motor Unpowered Motor and Feedback

Phasing

Cable Wires

Brushless Motors

DC Brush Motors

Stepper Motors

Cables

HyperWire

Cables and Accessories

cables, examining

CAN/CSA-C22.2 No. 61010-1

Check for fluids or electrically conductive material

exposure

Cleaning

connections, examining

Continuous Output Current specifications

Control Board Fuse Specifications

Control Supply Connections

Control Supply Connector

Mating Connector Part Numbers

Wiring Specifications

Control Supply specifications

cooling vents, inspecting

Customer order number

DC Brush Motor Configuration (Motor Power Output

Connector)

XC2 Hardware Manual

Index

www.aerotech.com

Summary of Contents for Automation1 XC2

































































































Search results

Summary of Contents for Automation1 XC2

Reviews:

Aerotech Automation1 XC2, Hardware Manual, Page: 91 / 96

Search results

Summary of Contents for Automation1 XC2

Reviews: