manualshive.com logo in svg

Advantech SKY-8101, User Manual

Share
Download
Advantech SKY-8101 User Manual Download Page 96

 

____________________________________________________________________________________________________ 

SKY-8101S Manual V04 20180321   

Copyright 2016 Advantech Co. Ltd. All rights reserved. 

  Page 94

 

3.3.2 Reinstalling the Top Cover   

 

Note!

 

You need: 

-    A PH2 screw driver 

 
To  re-install  the  top  cover  slide  it  onto  the  unit from  the  top  with  the  top  cover  flange 
facing  the unit

’s face plate.    Keep a gap of about an inch between the front plate and 

the  flange.  After  that,  slide  the  top  cover  forward  until  the  flange  is  fully  seated 
underneath the face plate. Now tighten the thumb screws and M3 screw. 

 

3.3.3 PCIe Card Installation 

 

Note!

 

You need: 

-    A PH2 screw driver 
-    PCIe cards are to be installed 

 
After removing the top cover, follow the instructions below: 
 
1. 

If  any  PCIe  cards  are  already  have  been  installed  before,  please  remove  all  IO 
cables and / or extra power cables connected to the PCIe cards. 

2. 

Loosen  the  thumb screws  that  secure the PCIe card  cage.  Make sure the thumb 
screws are fully disengaged. 

a.  Two  rear  thumb  screws  and  one  internal  thumb  screw  located  at 

①

  in 

below figure for the FH/FL card cage 

CG1.

 

b.  Two rear thumb screws for the Low profile card cage 

CG2.

 

3. 

Grab  the  card  cage  and  pull  the  card  cage  evenly  and  straight  to  the  top.  The 
pull/push  direction  must  be  with  an  angle  of  90

°

  from  the  PCIe  connector,  see 

below  figure.  You should feel a small 

“bump” when the riser card disengages with 

the motherboard. Keep pulling the card cage to the top until it is fully removed from 
the chassis and put it on the desk with the riser card connector facing towards you. 

4. 

Remove the blank plate(s) on the slot(s) you want to install a card / cards in using 
a PH2 screw driver. 

5. 

Remove the card holder at the rear side of the card cage. Make sure to retain the 
screws. 

6. 

Insert the card(s) to be installed. Make sure the card(s) align with the IO opening 
as well as the PCIe connector during installation. When installed, secure the card

’s 

face plate using the screw left over from removing the blank panel. 

7. 

If the PCIe cards need extra power supplies, connect the power cables to the PCIe 
cards 

8. 

Re-install the card holder. 

9. 

Turn  around  the card cage assembly and  re-insert  it into the SKY-8101S  system. 
Make  sure the  card  cage  is fully  seated  before you  fasten  the  thumb  screws  that 
hold the card cage in place. 

10.  If used, connect the PCIe power cables to the power distribution board. 

Summary of Contents for SKY-8101











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands