Advantech SKY-8101 User Manual Download Page 101

Page: 101 / 138

____________________________________________________________________________________________________

SKY-8200 Manual V04 20180321

Page 99

Reinstall the PCIe card cage and top cover.

Figure 3-25: M.2 SSD Installation

3.3.5 Memory Installation

After removing the top cover, follow the instructions below for DIMM installation:

Double check that the DIMMs be installed match the requirements of

section 2.4.6

and make sure you follow the DIMM population rules given in that section.

Open the white latches on the left and right sides of the DIMMs by turning it
outwards as indicated by the arrows below.

Figure 3-28: Opening DIMM Latches

Select DIMM orientation so that the keys in the DIMM module and socket match.

Figure 3-29: DIMM Key Alignment

Summary of Contents for SKY-8101











































































































































Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands

Advantech SKY-8101, User Manual

Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands