Advantech SKY-8101 User Manual Download Page 18

Page: 18 / 138

___________________________________________________________________________________________________

SKY-8101 Manual V04 20180321

Page 16

1.3 Installation and Configuration

The SKY-8101S comes as a pre-configured system with CPUs, memory and
peripherals installed in the unit. In the rare case that you procured a barebone system
or need to install components in the SKY-8101S for any other reason, please refer to

Section 3.3

1.3.1 Rack Mounting

The SKY-8101S server is designed to be as a rack server. Please follow the basic
guidelines below for rack mounting:

Mount the mounting ears on the each side of the unit using the screws included.

Note!
You need:

- A PH2 screw driver

1. Locate the threaded mount holes on the chassis on the side, close to the front

panel.

2. Place the mounting ear over the holes and insert the three screws. Do not tighten

the screws immediately.

Figure 1-1: Mounting Ear Screws Inserted Location

Summary of Contents for SKY-8101











































































































































Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands

Advantech SKY-8101, User Manual

Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands