manualshive.com logo in svg

Advantech SKY-8101, User Manual

Share
Download
Advantech SKY-8101 User Manual Download Page 104

 

____________________________________________________________________________________________________ 

SKY-8101S Manual V04 20180321   

Copyright 2016 Advantech Co. Ltd. All rights reserved. 

  Page 102

 

3.4 Firmware Upgrades 

Advanced  Platform  Management  allows  users  to  update  the  SKY-8101S  firmware  via 
the BMC

’s system or LAN interfaces using the HPM.1 protocol and related definitions. 

 

Firmware components supported include the BMC firmware itself as well as the system 
BIOS.  For  improved  reliability  most  updateable  components  support  a  backup  image 
stored in a dedicated, redundant flash chip. The BMC will perform an automatic rollback 
in case of an upgrade failure to recover the unit to its previous well known state. 
 

 

Note!

 

Please  note  that  BMC  functionality  of  BMC  will  be  degraded  while  uploading 
BMC  firmware.  Some  functionality  including  sensor  listing,  BMC  information 
etc, will not be available at that time. 

 

There are three components subject to firmware upgrades in the SKY-8101S: 

 

-  Component 0: BMC boot loader 

-  Component 1: BMC application firmware 

-  Component 2: FPGA 

-  Component 3: System BIOS 

-  Component 4: NVRAM 

 

 

Caution!

 

Please note that the BMC boot loader is a hardened and minimized firmware 
component which is not subject to field updates as it does not support fail safe 
updates via rollback capabilities. The upgrade capability of the boot loader is 
only  intended for factory  use.  A failing  update  in the field may leave the unit 
dysfunctional and may result in the requirement for on premise service access 
and / or RMA. 

 

ipmitool version 1.8.18 or later support HPM.1 firmware updates. This tool is part of all 
major Linux distributions. 
 

3.5 Replacing FRUs 

 

Caution!

 

Please  make  sure  you  follow  the  safety  guidelines  presented  in 

section1.1 

when making changes to the hardware. 

 
Unless otherwise noted in the sections below, removing the power to the unit / putting 
the unit out of service is not required. 

 

For  instruction  on  how  to  remove  and  install  the  top  cover  of  the  unit  please  refer  to 

section 3.3

. 

 

Summary of Contents for SKY-8101











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands