Advantech SKY-8101 User Manual Download Page 89

Page: 89 / 138

____________________________________________________________________________________________________

SKY-8200 Manual V04 20180321

Page 87

3.2.6 Post & Boot Menu

Users can configure the system boot priority settings via the boot page. The default
setting of boot priority of boot option #1 is “UEFI: Built-in EFI Shell”; Users can define the
boot priorities based on the application.

Figure 3-25: Post & Boot Menu

Table 3-17: Post & Boot Menu

Group

Setup Item

Access /
Options

Description

None

Setup Prompt
Timeout

Number of seconds to wait for
setup activation key.

Bootup NumLock
State

Select the keyboard NumLock
state.

Quiet Boot

Disabled

Enables or disables Quiet Boot
option.

Network Stack

Disabled

Enables or disables boot via
Network (PXE)

Boot Option Priority

User Defined

Sets the system boot order.

CSM16 Parameters

Option ROM
Messages

Force BIOS

Keep Current

CSM Parameters

CSM Support

Enable the CSM support

Summary of Contents for SKY-8101











































































































































Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands

Advantech SKY-8101, User Manual

Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands