Advantech SKY-8101 User Manual Download Page 37

Page: 37 / 138

____________________________________________________________________________________________________

SKY-8101S Manual V04 20180321

Page 35

2.4 Detail Description

2.4.1 Front Elements

Figure 2-3: Front Panel

Table 2-2: Front Elements

Item

Element

Description

Front LEDs

Front LEDs and buttons

– details below

Front I/O

Front I/O board with 1x micro-USB console
connector and 1x USB 3.0 port

Front cover

Front bezel with replaceable air filter

Key lock

Fan Modules

Five swappable fan modules allow service without
opening top cover / removing unit from rack

Fan Status LED

Fan status LED indicating power/ normal
operation and failure status

2.5

” Drive Bays

Four 2.5” SAS/SATA HDD/SSD bays

2.4.1.1 LEDs Details

The SKY-8101S supports an array of status LEDs and buttons at location

. The LEDs

are visible when the front cover is closed as well as when the front cover is open.

Summary of Contents for SKY-8101











































































































































Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands

Advantech SKY-8101, User Manual

Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands