![background image](http://html.mh-extra.com/html/advantech/data-acquisition-modules-adam-4000/data-acquisition-modules-adam-4000_user-manual_2857997143.webp)
Command Set
4-40 ADAM 4000 Series User’s Manual
ADAM-4080D Command Table
Command Syntax
Command Name
Command Description
Page
No.
%AANNTTCCFF
Configuration
Sets the address, input mode,
baud rate, checksum status and/or
frequency gate time for a specified
counter/ frequency module
7-28
$AA2
Configuration Status
Returns configuration parameters
from the specified
counter/frequency module
7-30
$AAF Read
Firmware
Version
Return firmware version code from
the specified counter/frequency
module
7-31
$AAM
Read Module Name
Return the module name from the
specified counter/frequency
module
7-32
$AABS
Set Input Signal
Mode
Sets the input signal mode of the
specified counter/frequency
module to either non-isolated or
photo-isolated input signals
7-33
$AAB
Read Input Signal
Mode
Read the input signal mode of the
specified counter/frequency
module.
7-34
#AAN
Read Counter or
Frequency Value
Returns the value of counter 0 or
counter 1 from a specified counter/
frequency module in hex format
7-35
$AA8V
Select LED Data
Origin
Select whether LED will display
data from the counter/frequency
module directly or from the host
computer
7-36
$AA8
Read LED Data
Origin
Returns the status of the LED Data
origin. Origin is either direct from
module or from host computer
7-37
$AA9(data)
Send Data to LED
The host computer sends data to
the addressed module to display
on its LED. This command is valid
only after selectting to display host
computer data ($AA8V)
7-38
(Continued on following page)
Summary of Contents for Data Acquisition Modules ADAM 4000
