5-52
ADAM 4000 Series User’s Manual
4011, 4011D, 4012, 4016
@AAEAT
Name
Enable
Alarm
command
Description
The addressed analog input module is instructed to enable
its alarm in either Latching or Momentary mode.
Syntax
@AAEAT(cr)
@
is a delimiter character.
AA
(range 00-FF) represents the 2-character hexadecimal
address of an analog input module.
EA
is the Enable Alarm command.
T
indicates alarm type and can have the value M =
Momentary alarm state, or L = Latching alarm state.
(cr)
represents terminating character, carriage return (0Dh).
Response
!AA(cr)
if the command was valid.
There is no response if the module detects a syntax error or
communication error or if the specified address does not
exist.
!
delimiter character indicates a valid command was
received.
AA
represents the 2-character hexadecimal address of the
responding analog input module.
(cr)
represents terminating character,
carriage return (0Dh).
Example
command:
@03EAL(cr)
response:
!03(cr)
The analog input module at address 03h is instructed to
enable its alarm in Latching mode.
The module confirms that the command has been received.
NOTICE: An analog input module requires a maximum of 2 seconds
after
it received an Enable Alarm command to let the settings take
effect . During this interval, the module can not be addressed to
perform any other actions.
Summary of Contents for Data Acquisition Modules ADAM 4000
