![background image](http://html.mh-extra.com/html/advantech/data-acquisition-modules-adam-4000/data-acquisition-modules-adam-4000_user-manual_2857997127.webp)
Command Set
4-24 ADAM 4000 Series User’s Manual
ADAM-4021 Command Table
Command Syntax
Command Name
Command Description
Page
No.
%AANNTTCCFF
Configuration
Set the address, output range,
baud rate, data format, slew rate
and/or checksum status
6-3
#AA(data)
Analog Data Out
Directs output data to a specified
module
6-6
$AA4 Start-up
output
current/voltage
configuration
Stores a default output value in a
specified module. The output
value will take effect upon startup.
6-8
$AA3(number of
counts)
Trim Calibration
Trims specified module a number
of units up/down
6-9
$AA0
4 mA Calibration
Tells the module to store
parameters for 4 mA Calibration
6-11
$AA1
20 mA Calibration
Tells the module to store
parameters for 20 mA Calibration
6-12
$AA2 Configuration
Status
Reads configuration of specified
module
6-13
$AA6 Last
Value
Readback
Returns either last value sent to
specified module by #AA
command, or start-up output
current/voltage
6-14
$AA8
Current Readback Returns measured value of the
current/voltage flowing through
current loop
6-15
$AA5
Reset Status
Checks if module has been reset
since the last $AA5 command
6-16
$AAF Read
Firmware
Version
Return the firmware version code
from the specified analog output
module
6-17
$AAM Read
Module
Name
Return the module name from the
specified analog output module
6-18
Summary of Contents for Data Acquisition Modules ADAM 4000
