manualshive.com logo in svg

ADEMCO VIDEO RapidView, Operation Manual

Share
Download
ADEMCO VIDEO RapidView Operation Manual Download Page 4

Operation Guide                

                                                      Rapid View

© Ademco Video 2002 MNRDVO250602US                                                     Page iii

Safety 
Notes

Safety Instructions

WARNING! Read these notes before       
attempting to operate the Rapid View

Refer all servicing to qualified personnel.
These products are for internal use only.
These products contain static electricity sensitive devices. 
Please take appropriate precautions when handling.
Handle the Rapid View with care, as improper handling may 
cause irreparable damage to the precision or sensitive parts 
within this unit.
Never point the camera directly towards a bright light source 
(for example sunlight), or expose the camera to intensive light 
situations as this may damage the camera pick-up device.

This information and our technical advice - whether verbal, in 
writing, or by way of trials - is given in good faith but without 
warranty and this also applies where proprietary rights of third 
parties are involved. Our advice does not release you from your 
obligation to check its validity and to test our products suitabil-
ity for the intended purpose(s) and use(s). The application, use 
and installation of our products either in isolation or in conjunc-
tion with other products used, provided and/or installed by you 
on the basis of our technical advice are beyond our control and           
therefore remain entirely your own responsibility. Ademco  
Video products are sold in accordance with our General        
Conditions of Sale and Delivery.

ALL DESIGNS AND SPECIFICATIONS ARE          

SUBJECT TO CHANGE WITHOUT NOTICE

© Ademco Video 2002

Summary of Contents for RapidView
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands