manualshive.com logo in svg

ADEMCO VIDEO RapidView, Operation Manual

Share
Download
ADEMCO VIDEO RapidView Operation Manual Download Page 13

Rapid View                                                                                              Operation Guide

Page 7                                                     © Ademco Video 2002 MNRDVO250602US

Chapter 2

4.0

Focus and Iris

Press the ‘AUTO FOCUS’ button to toggle the camera in and out of 
‘auto-focus’ mode, if the feature is available on the selected camera / 
receiver. (If the LED above the ‘AUTO FOCUS’ button is                        
illuminated, then ‘auto-focus’ mode is selected.) Press the ‘NEAR’ or       
‘FAR’ buttons to manually focus the camera. (The camera will            
automatically change to ‘manual focus’ mode if one of these two      
buttons is pressed.)

Press the ‘AUTO IRIS’ button to toggle the camera in and out of         
‘auto-iris’ mode, if the feature is available on the selected camera /      
receiver. (If the LED above the ‘AUTO IRIS’ button is illuminated, 
then ‘auto-iris’ mode is selected.) Press the ‘OPEN’ or ‘CLOSE’     
buttons to manually alter the camera iris.  (The camera will                    
automatically change to ‘manual iris’ mode if one of these two buttons 
is pressed.)

5.0

Manual Change Over

The operator can force the camera to change from MONO to COLOR 
or COLOR to MONO by pressing the ‘AUX’ button. The camera will 
automatically change back dependant on the illumination.

If the camera is in the mode selected by the operator (and is different 
to the mode that the camera would have automatically selected), the 
LED above the ‘AUX’ button is illuminated.

If the camera is in the mode that the camera has automatically selected, 
the LED above the ‘AUX’ button is off.

6.0

Wash, Wipe and Auxiliary Functions

If the receiver being controlled has WASH and WIPE functions, they 
are controlled as follows:

FOR WIPE.
Press the ‘WIPE’ button to activate the wiper.
Press the ‘WIPE’ button again to turn off the wiper.

Note:

If the LED above the ‘WIPE’ button is illuminated, 
the wiper is ON.

Summary of Contents for RapidView
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands