manualshive.com logo in svg

ADEMCO VIDEO RapidView, Operation Manual

Share
Download
ADEMCO VIDEO RapidView Operation Manual Download Page 39

Rapid View                                                                                              Operation Guide

Page 33                                                     © Ademco Video 2002 MNRDVO250602US

Chapter 5

justment does not include the desired phase setting, it will be neces-
sary to interchange the two AC supply wires

10.0

Remote Reset

10.1

Introduction

The Remote Reset enables you to reset the camera from the       
RapidView keyboard, i.e. you can reset the camera                   
without having to physically unplu+g it, or turn the power off      
then on again for a particular camera.

Note:

You will not be allowed to choose a different reset  
option after performing a reset leave the menu for 
approximatly 10 seconds

10.2

Operation 

The remote reset has three standard modes of operation

10.2.1 Power Up Reset

The power up reset allows you to reset the receiver and camera   
without the loss of any programmed options, i.e. presets, tours    
etc. Once the camera has reinitialized after a power up reset, it    
will return to its previous pan and tilt positions, zoom, iris and  
focus settings prior to the power up reset being executed.

This feature is found by pressing  ‘4’, ‘1’, ‘4’, ‘1’, ‘LOCK’.     
This will display the Engineer’s Menu, as shown in Figure ix.   
The ‘ADJUST SYNC’ menu option will be flashing.

Select the ‘REMOTE RESET’ via the joystick then press             
‘AUX’ to enter the remote reset menu as shown in Figure x.    

Summary of Contents for RapidView
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands