manualshive.com logo in svg

ADEMCO VIDEO RapidView, Operation Manual

Share
Download
ADEMCO VIDEO RapidView Operation Manual Download Page 12

Operation Guide                                                                                              Rapid View

© Ademco Video 2002 MNRDVO250602US                                                    Page 6

Chapter 2

2. Telemetry Functions

The Rapid View  range of handsets can control any Ademco Video    
telemetry receiver. The features that can be used depend upon the      
features that are available on the camera / receiver.

Under normal operation there is no audible beep when pressing the te-
lemetry function buttons.

When the touch sensitive joystick is used or when telemetry buttons 
are pressed, instructions are sent to the camera that is selected on the 
monitor under control, or monitor 1 on the Rapid View 8 / 2 K and      
16 / 2 K models. The instructions are not sent to the unselected        
cameras in the system.

The functions ‘WIPE’ and ‘AUTOPAN’ are latched functions (i.e. 
press once for ON, press again for OFF). When the latched function is 
ON, then the associated LED is also illuminated.

1.0

Pan and Tilt

Very precise control of pan and tilt can be achieved using the touch 
sensitive joystick. The speed of pan and tilt is relative to the force      
applied to the joystick.

2.0

Turn 180°

This function allows the camera to view a person who is walking       
underneath the camera.

Press the ‘180°’ button to pan the camera 180°.

The camera will pan 180° at the maximum speed. (Up to 400°    
per second.)

3.0

Zoom

Press the ‘ZOOM IN’ button to zoom in.
Press the ‘ZOOM OUT’ button to zoom out.

Summary of Contents for RapidView
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands