ACS-CONTROL-SYSTEM GmbH
l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
4
1. Brief description
2
1. Brief description
The panel meter instrument
M3-12
is a 5-digit device for direct voltage signals and a visual threshold value
monitoring via the display. The configuration happens via four keys at the front or by the optional PC
software PM-TOOL. The integrated programming interlock prevents unrequested chnages of parameters
and can be unlocked again with an individual code. Optional the following functions are available: a digital
input for triggering of Hold (Tara), two analog outputs and interfaces for further evaluating in the unit.
With help of the optional galvanic isolated setpoints, free adjustable limit values can be controlled and
reported to a superior master display.
The electrical connection is done via plug-in terminals on the back side.
Selectable functions like e.g. the recall of the min/max-value, an averaging of the measuring signals, a
nominal presetting or setpoint presetting, a direct threshold value regulation during operation mode and
further measuring setpoints for linearisation, complete the modern device concept.
2. Assembly
Sealin
g
48
,0
3,0
139
,0
M3
Gap for physical unit
1.
After removing the fixing elements, insert the device.
2.
Check the seal to make sure it fits securely.
3.
Click the fixing elements back into place and tighten the clamping screws by hand. Then use a
screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
Please read the
Safety advices
on
page 33
before installation and keep this user manual for future reference.
2. Assembly
The panel meter instrument DAL-311 is a 5-digit device for direct current signals and a visual
threshold value monitoring via the display. The configuration happens via 4 keys at the front or via the
optional PC software PM-TOOL. The integrated programming interlock prevents unrequested changes of
parameters and can be unlocked again with an individual code. Optional the following functions are
available: a supply for the sensor, a digital input for triggering of Hold (Tara), two analog outputs and
interfaces for further evaluating in the unit.
With help of the galvanic isolated setpoints (optional), free adjustable limit values can be controlled and
reported to a superior master display.
The electrical connection is done via plug-in terminals on the back side.
Selectable functions like e.g. the recall of the min/max-value, an averaging of the measuring signals, a
nominal presetting or setpoint presetting, a direct threshold value regulation during operation mode and
further measuring setpoints for linearisation, complete the modern device concept.
1. Brief description
2
1. Brief description
The panel meter instrument
M3-12
is a 5-digit device for direct voltage signals and a visual threshold value
monitoring via the display. The configuration happens via four keys at the front or by the optional PC
software PM-TOOL. The integrated programming interlock prevents unrequested chnages of parameters
and can be unlocked again with an individual code. Optional the following functions are available: a digital
input for triggering of Hold (Tara), two analog outputs and interfaces for further evaluating in the unit.
With help of the optional galvanic isolated setpoints, free adjustable limit values can be controlled and
reported to a superior master display.
The electrical connection is done via plug-in terminals on the back side.
Selectable functions like e.g. the recall of the min/max-value, an averaging of the measuring signals, a
nominal presetting or setpoint presetting, a direct threshold value regulation during operation mode and
further measuring setpoints for linearisation, complete the modern device concept.
2. Assembly
Sealin
g
48
,0
3,0
139
,0
M3
Gap for physical unit
1.
After removing the fixing elements, insert the device.
2.
Check the seal to make sure it fits securely.
3.
Click the fixing elements back into place and tighten the clamping screws by hand. Then use a
screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
Please read the
Safety advices
on
page 33
before installation and keep this user manual for future reference.
2. Assembly
