manualshive.com logo in svg

ABL eMH3, Installation Manual

Share
Download
ABL eMH3 Installation Manual Download Page 32

|     Configuring the Wallbox eMH3  –   

Data cable connection with the computer

32

 

ƒ

Order of wallboxes in the system

 

ƒ

Setting up data communication

Software access: 

Access via 

http://169.254.1.1:8300/

 after connecting a Controller wallbox to a PC

Description:

 

 "Set-up via Charge Point Administration application" on page 33 ff.

In both cases, the Controller Wallbox eMH3 must be connected to a suitable computer via the configuration kit CONF-

CAB (see next section).

Data cable connection with the computer

To connect the Wallbox eMH3 to a Windows PC, you will need the configuration kit CONFCAB (separately available 

accessory), which makes the wallbox's modbus interfaces compatible with the computer's USB port. Using CONFCAB 

components, any charging station from the Wallbox eMH3 product series can be connected by cable:

 

ƒ

1

 USB extension cable

 

ƒ

2

 USB to RJ45 adapter

 

ƒ

3

 RJ45 to individual strands patch cable

 

ƒ

4

 RJ45 to RJ12 patch cable

 

ƒ

5

 RJ45 to RJ45 patch cable

WARNING!

Data cabling using CONFCAB

Only use the cables and adapters contained in the CONFCAB kit to connect your Wallbox eMH3 to the computer. 

Otherwise, faultless communication cannot be guaranteed.

Proceed as follows to connect the Wallbox eMH3 with the computer by cable:

Controller Wallbox eMH3 with spring terminals  

(until mid-2021)

1 

Open the housing cover of the Controller wallbox as 

described in section "Preparing and fixing the wallbox 

in place" on page 17.

2 

Connect the patch cable 

3

 to the spring terminals 

located in the area near the hinge on the inside of the 

housing cover.

3 

Connect the USB extension cable 

1

 to one of the 

computer's USB ports.

4 

Use the USB to RJ45 adapter 

2

 to connect the patch 

cable 

3

 to the USB extension cable 

1

.

The wallbox is now connected to the computer by cable.

CONTROL*

METER

CONTROL*

METER

A M B A M B

A M B A M B

*evcc / rfid

CONTROL*

METER

ABL – Configuration Software

1

2

3

NOTE

Data cabling via LOMK218

All Wallboxes eMH3 with spring terminals can also be connected to a computer using the cable set LOMK218. 

You can find further information on this topic in section "Data cabling via LOMK218" on page 61.

Summary of Contents for eMH3



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands