ABL eMH3 Installation Manual Download

Page: 13 / 66

Installation –

Installation site requirements |

Installation

It is recommended to have the entire installation of the wallbox carried out by a qualified specialist electrical con-

tractor.

DANGER!

Dangerous electrical currents

Electrical installation, as well as final testing and certification for operation must be carried out by a qualified

specialist electrical contractor, who, on the basis of their specialist training and experience, as well as their

knowledge of the relevant standards, is able to assess and carry out the working steps described in this manual

and recognise potential hazards.

NOTE

Identical installation for Single and Twin variants

The Wallbox eMH3 is available as a Single (one charge point) or Twin (two charge points) variant. In principle, in-

stallation and commissioning are identical. However, the working steps described may need to be applied to both

charge points.

Installation site requirements

Your wallbox is suitable for outdoor use. Please note, however, that the permissible ambient conditions (see "Technical

specifications" on page 55) must be adhered to in order to guarantee the functionality of your wallbox at all times.

The installation site must be freely accessible.

The mounting surface must be level and solid.

The mounting surface must measure at least 492 × 400 mm

(height x width).

400 mm

492 mm

The installation height should be between 120 and 140 cm

(ground to bottom edge of housing).

120 ~ 140 cm

Summary of Contents for eMH3



































































Search results

Summary of Contents for eMH3

Reviews:

Related manuals for eMH3

Brands by name

Popular brands

ABL eMH3, Installation Manual

Search results

Summary of Contents for eMH3

Reviews:

Related manuals for eMH3

Brands by name

Popular brands