ABB Relion SAM600-IO Protocol Manual Download

Page: 7 / 108

Table of contents

Section 1 Introduction.......................................................................5

This manual........................................................................................ 5
Intended audience.............................................................................. 5
Product documentation.......................................................................6

Product documentation set............................................................6
Document revision history............................................................. 7
Related documents........................................................................7

Document symbols and conventions..................................................8

Symbols.........................................................................................8
Document conventions..................................................................9

IEC 61850 edition 1 / edition 2 mapping.............................................9

Section 2 Introduction to IEC 61850...............................................11

Overview...........................................................................................11
Related documentation to IEC 61850...............................................12

Section 3 Substation Configuration description Language (SCL).. 15

The substation section......................................................................16
The communication section..............................................................17
The IED section................................................................................ 18
Tool concept..................................................................................... 20
Engineering concept in IEC 61850-6................................................21

Section 4 Communication profile....................................................23

Section 5 Supported services.........................................................25

Section 6 Data sets and control blocks.......................................... 27

Data sets.......................................................................................... 27
Report control block (URCB/BRCB)................................................. 28
GOOSE Control Blocks (GoCB)....................................................... 31

Section 7 Logical node data model................................................ 35

Common data objects in each logical node......................................35
Logical nodes for control.................................................................. 37

Bay control CBAY........................................................................37

Bay control QCBAY................................................................37

Switch controller CSWI................................................................39

Switch controller SCSWI........................................................ 39

Logical nodes for conversion functions............................................ 41

Integer to Boolean converter FCVB.............................................41

Table of contents

Switchgear control unit SAM600-IO Version 2.2 IEC

Communication protocol manual

Summary of Contents for Relion SAM600-IO












































































































Search results

Summary of Contents for Relion SAM600-IO

Reviews:

Related manuals for Relion SAM600-IO

Brands by name

Popular brands

ABB Relion SAM600-IO, Protocol Manual

Search results

Summary of Contents for Relion SAM600-IO

Reviews:

Related manuals for Relion SAM600-IO

Brands by name

Popular brands