ABB Relion SAM600-IO Protocol Manual Download Page 30

Page: 30 / 108

GOOSE

TimeSync
(SNTP)

MMS Protocol Suite

GSSE

TCP/IP

T-Profile

ISO CO

T-Profile

ISO/IEC 8802-2 LLC

GSSE

T-Profile

UDP/IP

ISO/IEC 8802-3 Ethertype

Sampled
Values
(Multicast)

Generic
Object
Oriented
Substation
Event

Time
Sync

Core
ACSI
Services

Generic
Substation
Status
Event

ISO/IEC 8802-3

IEC09000153-1-en.vsd

IEC09000153 V1 EN-US

Figure 7:

Overview of functionality and profiles according to IEC 61850-8-1

Out of this content, the implementation supports:

•

GOOSE

•

TimeSync using SNTP

•

The peer-to-peer/vertical communication using MMS protocol suite with the
T-profile TCP/IP

For each of the above, the resulting underlying protocols as stated in Figure

See the PICS and PIXIT for more information.

Section 4

1MRK 511 440-UEN A

Communication profile

Switchgear control unit SAM600-IO Version 2.2 IEC

Communication protocol manual

Summary of Contents for Relion SAM600-IO












































































































Search results

Summary of Contents for Relion SAM600-IO

Reviews:

Brands by name

Popular brands

ABB Relion SAM600-IO, Protocol Manual

Search results

Summary of Contents for Relion SAM600-IO

Reviews:

Brands by name

Popular brands