ABB REACT-3.6-TL Product Manual Download Page 171

- 171 -

000043DG

8 - Maintenance

M

easuring the insulation resistance of photovoltaic generator

To measure the insulation resistance of the PV generator compared to 
ground 

, the two poles of the PV generator must be short-circuited 

(using a suitably sized switch).

+

_

IG

Once the short-circuit has been made, measure the insulation resistance 
(Riso) using a megohmmeter positioned between the two shorted poles 
and ground (of the inverter). 

Mega

Inverter

IG

+

_

-TL MODELS (transformerless). 

If the measured insulation resistance 

(Riso) is less than 1Mohm the inverter does not connect to the grid due 
to a low insulation of photovoltaic generator respect to ground. 

-I MODELS (with high frequency transformer). 

If the measured insu-

lation resistance ( Riso in case of input poles floating respect to ground 

or QF=1 if the one of input poles is grounded) is less than 0.2Mohm the 
inverter does not connect to the grid due to a low insulation of photovol-
taic generator respect to ground. 

The insulation resistance is affected by the environmental conditions the PV generator is in 
(E.g.: photovoltaic module wet from dump or rain), and therefore the measurement must be 
made immediately after the anomaly 

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Summary of Contents for REACT-3.6-TL















































































































































































Reviews: