manualshive.com logo in svg

ABB REACT-3.6-TL, Product Manual

Share
Download
ABB REACT-3.6-TL Product Manual Download Page 141

- 141 -

000569BG

7 - Operation

> Statistics

> Self consumpti.

> Self sufficien.

> Ener. from grid

> Ener. to grid

> Ener. to load

> PV en. to load

> PV ener.

> Settings

> Info

> Measures

> Set time

 Password 0000

> Set cash

> Set RS485 com

> Country Select

> New password

> SD Update Info

> Energy Policy

Inverter

> Statistics

> Settings

> Vstart

> Input mode 

> Input UV Delay

> Service

> Info

> Part No.

> Serial No.

> Firmware

> Remote ON/OFF

> MPPT Scan

> Power Limit.

> Reactive Power

> Autotest

> Alarms

> Backup

> Lifetime

> Partial

> Today

> Last 7 days

> Last 30 days

> Last 365 days

> User Period

Display

> Settings

> Backlight

> Contrast

> Buzzer

> Power Graph

> Language

Meter

> Settings

> Info

> Type

> Part No.

> Serial No.

> FW Rel.

> Measures

> Voltage

> Active Power

> Line current

> Load current

> Frequency

> Meter model

> Meter Address

> Meter com

Battery

> General

**

****

Load Manager

> info

> Relay Status

****

WIFI Logger

> Settings

> Info

> Part No.

> Serial No.

> View IP

> View Mode

> Restore AP

*

System

****

 Password 0000

 Password 0000

 Password 0000

> Settings

> Info

> Nom. Cap

> Measures

> Ibat

> Vbat

> Pbat

> RE

> SOC

> SOH

> RT

> Battery Model

> Battery Packs

 Password 0000

> Pack 1

> Settings

> Info

> Device Name 

> Serial No.

> FW Rel.

> Nom. Capacity

> Init. Capacity

> Status

> Warning

> Alarms

> Measures

> Pack 1 enable 

> Smoke Sensor

 Password 0000

> Statistics

> Energy dischar.

> E-day

> E-7d

> E-30d

> E-365

> E-tot

> Ibat

> Vbat

> Pbat

> Tbat

> FCC

> RC

> RE

> TED

> SOC

> SOH

> TUT

> TDT

> RT

> CC

Meter > Measure

Select the 

Measure

 menu to access the following sub-menus:

1.  Voltage

Grid voltage value. Depending on the type of meter connected it is pos-
sible to have a single value L1 (for the single-phase) or three values L1, 
L2 and L3 (for the three-phase).

2.  Active power

Value of active power delivered by system. Depending on the type of 
meter connected it is possible to have a single value L1 (for the single-
phase) or three values L1, L2 and L3 (for the three-phase).

3.  Line current

Value of current fed into or taken from the grid. Depending on the type of 
meter connected, it is possible to have a single value IL1 (for the single-
phase) or three values IL1, IL2 and IL3 (for the three-phase).

4.  Load current

Value of current used to power domestic loads. Depending on the type of 
meter connected it is possible to have a single value IL1-L (for the single-
phase) or three values IL1-L, IL2-L and IL3-L (for the three-phase).

5.  Frequency

Grid frequency value.

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Summary of Contents for REACT-3.6-TL















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands