manualshive.com logo in svg

ABB REACT-3.6-TL, Product Manual

Share
Download
ABB REACT-3.6-TL Product Manual Download Page 131

- 131 -

000569BG

7 - Operation

Parameter

Description

Set F Derating

F Der. Mode. 

Select power derating in the event of grid 

over-frequency.

F Der. Res. T. 

Time period after OF derating in which the 

inverter checks that the frequency is back within the opera-
ting ranges (parameters “F<Connect” “F>Connect”) requi-
red by the grid standard before ramping up the output from 
the derating condition.

F Der. Del. T. 

Setting deliberate delay before going into 

derating

Set VRT

Set Zero P Th

. Sets the voltage threshold at which the 

inverter interrupts the export of energy to the grid.

Set FRT

Set Zero P Th

. Sets the frequency threshold at which the 

inverter interrupts the export of energy to the grid.

Set Backup

Allows the Stand Alone accessory board to be enabled/
disabled. Once this mode is enabled, the guided setup will 
automatically start.

Reset Latch

Allows the active alarms preventing the system from ope-
rating (Latch) to be reset manually

5. Remote ON/OFF

This section of the menu is used to enable / disable connection/discon-
nection of the inverter from the grid using the special control signal (

REM

).

• Disable:

 the connection/disconnection of the inverter to/from the grid is 

dictated by the input (voltage from the photovoltaic generator) and output 
(grid voltage) parameters of the inverter.

• Enable:

 connection/disconnection of the inverter to/from the grid is dic-

tated (as well as by the inverter input - voltage from photovoltaic genera-
tor - and output parameters - grid voltage) by the state of the remote On/
Off signal.

6. MPPT Scan

This section of the menu allows you to set the parameters of the maxi-
mum power point search (MPPT) function. This function is useful when 
there are areas of shade on the PV generator, which may create several 
points of maximum power on the operating curve.

• E/D MPPT Scan:

 Enables/Disables the scan for identifying the maxi-

mum power point of the system.

• Scan Interval: 

This section allows you to set the time between scans. 

Remember that the shorter the scan interval the greater the loss of pro-
duction, due to the fact that energy is transferred to the grid during the 
scan but not at the maximum power point. Each scan takes 2 seconds.

7. Power Limit.

This section of the menu allows you to adjust the limit to the active power 
that the inverter can feed into the grid by setting the percentage of nomi-
nal power at which the limit should be triggered.
Setting it to 100% resets the default maximum power, which in some 
installation country standards may be 110% of nominal power

> Statistics

> Self consumpti.

> Self sufficien.

> Ener. from grid

> Ener. to grid

> Ener. to load

> PV en. to load

> PV ener.

> Settings

> Info

> Measures

> Set time

 Password 0000

> Set cash

> Set RS485 com

> Country Select

> New password

> SD Update Info

> Energy Policy

Inverter

> Statistics

> Settings

> Vstart

> Input mode 

> Input UV Delay

> Service

> Info

> Part No.

> Serial No.

> Firmware

> Remote ON/OFF

> MPPT Scan

> Power Limit.

> Reactive Power

> Autotest

> Alarms

> Backup

> Lifetime

> Partial

> Today

> Last 7 days

> Last 30 days

> Last 365 days

> User Period

Display

> Settings

> Backlight

> Contrast

> Buzzer

> Power Graph

> Language

Meter

> Settings

> Info

> Type

> Part No.

> Serial No.

> FW Rel.

> Measures

> Voltage

> Active Power

> Line current

> Load current

> Frequency

> Meter model

> Meter Address

> Meter com

Battery

> General

**

****

Load Manager

> info

> Relay Status

****

WIFI Logger

> Settings

> Info

> Part No.

> Serial No.

> View IP

> View Mode

> Restore AP

*

System

****

 Password 0000

 Password 0000

 Password 0000

> Settings

> Info

> Nom. Cap

> Measures

> Ibat

> Vbat

> Pbat

> RE

> SOC

> SOH

> RT

> Battery Model

> Battery Packs

 Password 0000

> Pack 1

> Settings

> Info

> Device Name 

> Serial No.

> FW Rel.

> Nom. Capacity

> Init. Capacity

> Status

> Warning

> Alarms

> Measures

> Pack 1 enable 

> Smoke Sensor

 Password 0000

> Statistics

> Energy dischar.

> E-day

> E-7d

> E-30d

> E-365

> E-tot

> Ibat

> Vbat

> Pbat

> Tbat

> FCC

> RC

> RE

> TED

> SOC

> SOH

> TUT

> TDT

> RT

> CC

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Summary of Contents for REACT-3.6-TL















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands