manualshive.com logo in svg

ABB REACT-3.6-TL, Product Manual

Share
Download
ABB REACT-3.6-TL Product Manual Download Page 137

- 137 -

000569BG

7 - Operation

If the alarm condition is persistent, the relay will remain activated 
(status:switched)

• Latch configurable alarm (display text “Al. Conf. Latch”)

INVERTER RUN

SELECTED 

ERROR/WARNING

 OCCURENCY 

ERROR MESSAGE

t=15s

GRID RECONNECTION

t=based on Country Standard

ERROR/WARNING 

STILL

PRESENT

Yes

No

N.C.

N.O.

N.C.

N.O.

Relay State: 

Idle

Relay State: Switched

N.C.

N.O.

Relay State: Switched

The relay is activated (status: 

switched) whenever an error (code 
Exxx) or a warning (code Wxxx) is 
among those selected from the list in 
the dedicated submenu 

Alarm Config 

(see the table below). The contact re-
turns to its resting position when the 
inverter returns to its normal operating 
state and reconnects to the grid.

Selectable alarms for which the relay is activated

E001

E002

E003

E004

E005

E006

E007

E009

E010

E011

E012

E013

E014

E015

E016

E017

E018

E019

E020

E021

E022

E023

E024

E025

E026

E027

E028

E029

E030

E031

E032

E033

E034

E035

E036

E037

E046

E050

E053

E054

E055

E056

E057

E058

E077

E078

E081

E084

E089

W001

W002

W003

W004

W005

W006

W007

W009

W011

W015

W046

W047

W048

W051

W058

W059

If the alarm condition is persistent, the relay will remain activated 
(status:switched)

• Ext configurable alarm (display text “Al. Conf. Ext.”)

In this mode, it is possible to configure the behaviour of the alarm relay 

according to an external error table which can be setup with the Aurora 
Manager LITE software. In the table it is possible to select the alarms 

> Statistics

> Self consumpti.

> Self sufficien.

> Ener. from grid

> Ener. to grid

> Ener. to load

> PV en. to load

> PV ener.

> Settings

> Info

> Measures

> Set time

 Password 0000

> Set cash

> Set RS485 com

> Country Select

> New password

> SD Update Info

> Energy Policy

Inverter

> Statistics

> Settings

> Vstart

> Input mode 

> Input UV Delay

> Service

> Info

> Part No.

> Serial No.

> Firmware

> Remote ON/OFF

> MPPT Scan

> Power Limit.

> Reactive Power

> Autotest

> Alarms

> Backup

> Lifetime

> Partial

> Today

> Last 7 days

> Last 30 days

> Last 365 days

> User Period

Display

> Settings

> Backlight

> Contrast

> Buzzer

> Power Graph

> Language

Meter

> Settings

> Info

> Type

> Part No.

> Serial No.

> FW Rel.

> Measures

> Voltage

> Active Power

> Line current

> Load current

> Frequency

> Meter model

> Meter Address

> Meter com

Battery

> General

**

****

Load Manager

> info

> Relay Status

****

WIFI Logger

> Settings

> Info

> Part No.

> Serial No.

> View IP

> View Mode

> Restore AP

*

System

****

 Password 0000

 Password 0000

 Password 0000

> Settings

> Info

> Nom. Cap

> Measures

> Ibat

> Vbat

> Pbat

> RE

> SOC

> SOH

> RT

> Battery Model

> Battery Packs

 Password 0000

> Pack 1

> Settings

> Info

> Device Name 

> Serial No.

> FW Rel.

> Nom. Capacity

> Init. Capacity

> Status

> Warning

> Alarms

> Measures

> Pack 1 enable 

> Smoke Sensor

 Password 0000

> Statistics

> Energy dischar.

> E-day

> E-7d

> E-30d

> E-365

> E-tot

> Ibat

> Vbat

> Pbat

> Tbat

> FCC

> RC

> RE

> TED

> SOC

> SOH

> TUT

> TDT

> RT

> CC

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Summary of Contents for REACT-3.6-TL















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands