ABB PGC2000 Operation And Service Manual Download | Manualshive

Page: 174 / 400

background image

6-4

2000-OSM, F1

b. The gases may be pure, but contaminated tubing or hardware components in the analyzer or

cylinder regulator(s) contaminate the makeup gases as they pass through them. The FID
detects theses contaminants, resulting in a noisy baseline.

c. An FID is generally equipped with a catalytic air cleanup unit to remove hydrocarbon

impurities from the burner air. If the air cleanup unit fails, the impurities in the burner air can
appear as detector noise.

4. A continuous presence of sample at the detector due to sample valve leakage. Perform

Test

Procedure 3

(Sample Valve Leaking/Column Flooding).

5. Electronics circuit failure. Replace FID Amplifier Assembly.

Baseline Signal Random Noise (FID)

Symptom: Baseline characterized by random noise and/or spikes (see Figure 6-6).

NORMAL

NOISE

Figure 6-6. BASELINE RANDOM NOISE

Cause: FID noise is generally the result of electrical noise or contamination.

1. Electrical noise is usually isolated to a defective FID amplifier, defective coaxial cable or faulty

electrical connections.

a. Electrical noise from the FID amplifier could result from a noisy power supply or defective

component of the PCB.

b. Loose electrical connections can cause electrical signals to be sporadic.

c. Since the FID amplifier input impedances are extremely high, low noise coaxial cable

connects the detector and the FID amplifier. Defective coaxial cables or poor electrical
connections are often sources of noise.

2. Contamination can enter through the burner air, burner fuel, or carrier. Secondary sources are

contaminated air, fuel, carrier lines, or regulators.

a. Hydrocarbon contaminates in carrier gas, hydrogen fuel or air can cause the FID to produce

an output signal as they are burned.

b. The gases may be pure, but contaminated tubing or hardware components in the analyzer or

cylinder regulator(s) contaminate the makeup gases as they pass through them. The FID
detects theses contaminants, resulting in a noisy baseline.

c. An FID is generally equipped with a catalytic air cleanup unit to remove hydrocarbon

impurities from the burner air. If the air cleanup unit fails, the impurities in the burner air can
appear as detector noise.

d. If water accumulates in the FID vent, the detector effluent flow can bubble through the

accumulated water. This in effect back-pressures the FID, causing the flame intensity to
fluctuate. This can appear as a noisy baseline as well.

«
...
172
173
174
175
176
...
»

Summary of Contents for PGC2000

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for PGC2000

Precision2 HP2 Series

Brand: B-K lighting Pages: 6

Brand: Zero Hand Truck Pages: 38

Brand: B-K lighting Pages: 3

Brand: Garelick Pages: 4

Brand: Yamaha Pages: 5

Brand: MAKSIWA Pages: 155

Brand: Xtricity Pages: 4

Brand: Hammer Strength Pages: 8

Brand: Kettler Pages: 20

Brand: Beamz professional Pages: 24

Brand: Ibiza sound Pages: 12

Brand: Agilent Technologies Pages: 6

ARCH RIVAL CR4250-S

Brand: Big Game Treestands Pages: 30

Brand: Samson Pages: 20

Brand: OttLite Pages: 5

Brand: Analytic Jena Pages: 62

Brand: olympia electronics Pages: 4

Brand: W&H Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands