ABB IRB 6620 - 150/2.2 Product Manual Download

Page: 221 / 303

4 Repair

4.6.5. Replacement of motor, axis 5

219

3HAC027151-001 Revision: B

rig

t 200

200

8 ABB. All righ

ts reser

ed.

Refitting, motor, axis 5

The procedure below details how to refit motor, axis 5.

14. Remove the motor by gently lifting it straight out. Keep track of the shims between the

motor flange and the wrist housing.

Action

Note

Action

Note

DANGER!

Turn off all electric power, hydraulic and
pneumatic pressure supplies to the robot!

2. Make sure the

o-ring

on the circumference of

the motor is seated properly. Lightly lubricate
the

o-ring

with

grease.

Art. no. is specified in

Required

equipment on page 217

3. In order to release the brake, connect the 24

VDC power supply.

Connect to:

- connector R2.MP5 (in the motor):

•

+ : pin 2

•

- : pin 5

4. Fit the two

guide pins

in two of the motor

attachment holes.

Art. no. is specified in

Required

equipment on page 217

5. Fit the motor, with guidance from the pins,

making sure the motor pinion is properly mated
to the gear of axis 5.

Make sure the motor pinion does not
get damaged!

6. Secure the motor with four attachment screws

and plain washers.

4 pcs: M8 x 25; tightening torque: 24
Nm.

7. Disconnect the brake release voltage.

8. Refit the cable of the axis 5 motor and

reconnect all connectors beneath the motor
cover.

9. Refit the cover on top of the motor with its four

attachment screws.

10. Refit the cable gland cover at the cable exit

with its two attachment screws.

Make sure the cover is tightly sealed!

11. Refit the

metal clamp

securing the cable

harness.

Shown in the figure in section

Location

of motor on page 217

12. Perform a leak-down test.

Detailed in section

Performing a leak-

down test on page 148

13. Refit the cover of the wrist unit with its

attachment screws.

14. Refill the gear with oil.

Detailed in section

Oil change,

gearbox, axis 5 on page 137

15. Recalibrate the robot.

Calibration is detailed in a separate
calibration manual, enclosed with the
calibration tools.

General calibration information is
included in section

Calibration informa-

tion

Continued

Continues on next page

Summary of Contents for IRB 6620 - 150/2.2




































































































































































































































































































Search results

Summary of Contents for IRB 6620 - 150/2.2

Reviews:

Related manuals for IRB 6620 - 150/2.2

Brands by name

Popular brands

ABB IRB 6620 - 150/2.2, Product Manual

Search results

Summary of Contents for IRB 6620 - 150/2.2

Reviews:

Related manuals for IRB 6620 - 150/2.2

Brands by name

Popular brands