ABB ACS880-1604LC Hardware Manual Download Page 129

Page: 129 / 200

Dimensions and weights

￭

R8i DC/DC converter module

The dimensions of a DC/DC converter module are:

•

height 880 mm

•

width 210 mm

•

depth 450 mm

•

weight 63 kg.

For the number of R8i modules in a given DC/DC converter unit, see

Type equivalence

table

￭

BDCL filter module

The dimensions of the BDCL module are:

•

height 1009 mm (39.72 in)

•

width 240 mm (9.45 in)

•

depth 436 mm (17.17 in)

•

weight BDCL-14LC-7 235 kg (518.0 lb) and BDCL-15LC-7 265 kg (584.2 lb) .

One filter module is needed for each converter module.

Free space requirements

•

Left and right sides, front and back: None

•

Below: Space needed by heat exchanger and cooling fan.

•

Above: The cooling air flow through the module should not be restricted.

Technical data 129

Summary of Contents for ACS880-1604LC








































































































































































































Search results

Summary of Contents for ACS880-1604LC

Reviews:

Related manuals for ACS880-1604LC

Brands by name

Popular brands

ABB ACS880-1604LC, Hardware Manual

Search results

Summary of Contents for ACS880-1604LC

Reviews:

Related manuals for ACS880-1604LC

Brands by name

Popular brands