manualshive.com logo in svg

AB Regin Corrigo E81D-3, Manual, Page: 97 / 118

Share
Download
AB Regin Corrigo E81D-3 Manual Download Page 97

Manual Corrigo Ventilation, revision R 

Chapter 17 

  Configuration 

97  

17.29 Communication 

17.29.1 Modbus communication 

Corrigo can be connected to a network for Modbus communication. 

Modbus slave com- 
munication, Port 1 
Not Active 
 

If Modbus communication is activated, you can set the address etc. 

Modbus communication takes place using 1 stop bit. 

Modbus Address: 1 
Speed: 9600 bps 
Two stop bits:Yes 
Parity:No 

NOTE:

 Only one stop bit can be used. 

Slave 

For connection to E tool

©

 and a Modbus SCADA system. 

Function Port1   

 

Slave 
 
 

Expansion unit 

In order to connect additional I/Os (in- and outputs) to the Corrigo, port 1 or 2 should be set as an 
expansion unit (only Corrigo controllers can be connected). It is possible to connect two expansion 
units, giving a maximum number of 28*3 = 84 inputs/outputs. The expansion units must have the 
addresses 241:1 and 241:2 respectively (ELA:PLA). 

Expansion unit 1 
None 
Expansion unit 2 
None 

To initiate the expanded controllers, select ”Expansion unit” at start-up (see below). If the controller 
does not contain program version 3.0 or later, the initiation must be made via E tool

©

  (see the E 

tool

©

 manual). However, this requires that the controller hardware is of a second generation Corrigo 

(…S). After initiating the expansion units and setting the master controller, all inputs and outputs 
are available for configuration in the master controller under "Configuration" / "Inputs/Outputs" (the 
expansion units’ in-/outputs are named Exp1/Exp2).  

Ventilation 
Heating 
Boiler 
Expansion Unit 1 
Expansion Unit 2 

Frequency converters 

Up to two separate Vacon NXL / Lenze SMV / Omron V1000 / Emerson Commander / LS iG5a / 
LS iS7 / EBM-PABST / Danfoss FC 101 frequency converters can be controlled via Modbus 
communication. Miscellaneous alarms and indications can be read from the frequency converters. 
For a complete list of alarms, see the alarm list. For communication addresses, see the Corrigo 
variable list. Information is also available at the end of this manual. 

The Corrigo Modbus settings are listed below. They are not adjustable and must also be set in the 
Vacon NXL/Lenze SMV/Omron V1000/Emerson Commander/ LS iG5a / LS iS7 / EBM-PABST / 
Danfoss FC 101 frequency converters. 

Summary of Contents for Corrigo E81D-3























































































































Reviews:

No comments