manualshive.com logo in svg

AB Regin Corrigo E81D-3, Manual, Page: 108 / 118

Share
Download
AB Regin Corrigo E81D-3 Manual Download Page 108

 

108 

Chapter 18 

  Other functions 

Manual Corrigo Ventilation, revision R 

Choose language 
English 
 
 

In the second menu, the setpoint is set. The appearance of the menu depends on which control type 
has been configured. 

Supply air temp 
Setp.: 18°C 
 
 

In the third menu, time and date are set. 

Time: 14:27 
   Date: 2013-11-25 
Weekday: Tuesday 
 

 In the fourth menu, the running time for normal speed Monday – Friday is set. 

Normal speed 

Monday 

 Friday 

Per 1: 07:00 – 16:00 
Per2: 00:00 – 00:00 

In the fifth menu, the running time for normal speed Saturday, Sunday and holiday is set. 

Normal speed 

Saturday 

 Holiday 

Per 1: 00:00 – 00:00 
Per2: 00:00 – 00:00 

If 2-speed fans or pressure/flow controlled fans have been configured, the corresponding times for 
reduced speed will be displayed in the sixth and seventh menus. 

Reduced speed 

Monday 

 Friday 

Per 1: 07:00 – 16:00 
Per2: 00:00 – 00:00 

 

Reduced speed 

Saturday 

 Holiday 

Per 1: 00:00 – 00:00 
Per2: 00:00 – 00:00 

The last menu is used to turn off the wizard, and the Corrigo will switch to normal running mode. 
The selected values will be used. 

The wizard will not be shown again during further use. 

 

 

Summary of Contents for Corrigo E81D-3























































































































Reviews:

No comments