manualshive.com logo in svg

AB Regin Corrigo E81D-3, Manual, Page: 73 / 118

Share
Download
AB Regin Corrigo E81D-3 Manual Download Page 73

Manual Corrigo Ventilation, revision R 

Chapter 15 

  Settings 

73  

Shutdown mode 

Shutdown mode 
P-band: 100.0 °C 
I-time: 100  sec 
 

Frost protection temperature 

Frost protection 

temperature 

 

 
  

 

Frost protection 
Active 
Setp shutdown: 25°C 
P-band active: 5°C 

 

Fast stop at  
frost-protection alarm 
Yes 
 

"Setp shutdown" is the shutdown mode setpoint. 

P-band active 5°C means that the frost protection controller will start overriding the heating output 
when the frost protection temperature is less than five degrees above the set frost alarm limit. The 
default alarm limit is 7°C. It can be changed in the menu Settings/Alarm settings/Alarm 
limits/Alarm limit frost protection. 

Exchanger de-icing 

De-iceing 
P-band: 100 °C 
I-time: 100  sec 
 

15.2 Control pressure 

Pressure control SAF 

Pressure control SAF 
P-band:  500 Pa 
 I-time:  60 sec 
Min Output: 0   % 

Pressure control EAF 

Pressure control EAF 
P-band:  500 Pa 
 I-time:  60 sec 
Min Output: 0   % 

15.3 Control flow 

Flow control SAF 

Flow control SAF 
P-band:  1000 m3/h 
 I-time:  60 sec 
Min Output: 0   % 

Summary of Contents for Corrigo E81D-3























































































































Reviews:

No comments